LGB 20410 Instruction Manual Download Page 6

Page: 6 / 12

Replacing the traction tire

- Under the model, remove two

screws on each end of the gearbox.

- Carefully pull the gearbox out of the

model.

- Carefully unplug the wiring cable.
- Use a small, straight-blade screw-

driver to replace the traction tire:

- Pry the old traction tire out of the

wheel groove.

- Gently insert the new traction tire

into the wheel groove.

- Make sure that the traction tire

is seated properly in the wheel
groove.

- Reassemble.

Maintenance parts

50010 Smoke and Cleaning Fluid
50019 Maintenance Oil
51020 Gear Lubricant
63120 Brushes, Assembled,

14 mm and 16 mm, 8 pieces

63218 Standard Pick-Up Shoes,

2 pieces

68511 Plug-In Bulb, Clear, 5V,

10 pieces

INSTRUCTIONS FOR ADVANCED
USERS

MTS Onboard Decoder

Programming functions

You can program numerous func-
tions of the onboard decoder to suit
your requirements. If you want to do
this, program the “function values”
in “registers” (CVs) using a PC and
the 55045 MTS PC Decoder
Programming Module. You can also
program the function values using a
55015 Universal Remote.

Hints:

- For normal operation, it is not nec-

essary to change the function val-
ues.

- If programming results in unsatis-

factory operation, you can repro-
gram the factory pre-set values of
most important CVs: Program reg-
ister CV55 to function value 55.
This also reprograms the loco
address to the factory pre-set
value.

To reprogram the factory pre-set
function values with the 55015 (dis-
plays shows “P --”) input 6, 5, and 5
and press the right arrow button. The
display shows “P --” again: Input 5,
5, and 5 and press the right arrow
button again.

When operating with the Multi-Train
System, the loco features a “Back-
EMF” function. This keeps the motor
speed constant (and under normal
conditions the loco speed), even
when the load of the loco changes,
for example, in curves or on grades.
This feature does not work at top
speed, because additional voltage
must be available to overcome any
added load.
If desired, numerous functions of the
onboard decoder, such as accelera-
tion, braking, direction of travel and
many others, can be programmed
using a PC and the 55045 MTS PC
Decoder Programming Module (see

Instructions for advanced users

These functions also can be pro-
grammed from the 55015 Universal
Remote.

Lighting

This model features directional light-
ing: three lights on the front, one on
the rear. The model has a "flat" multi-
purpose socket, with a removable
cover, on the rear of the cab (Fig. 3).
This socket can be used to provide
track power to LGB cars with lighting
or sound electronics.
To remove the cover of the socket,
pull it straight out. If the cover is
tight, gently use a small straight
screwdriver to pry it out. (Do not pull
out the rectangular outer housing.)

Power Supply
Attention!

For safety and reliability,

operate this model with LGB power
supplies (transformers, power packs
and controls) only. The use of non-
LGB power supplies will void your
warranty.
Use this model with LGB power sup-
plies

with an output of at least 1 amp.

For more information on LGB power
supplies for indoor, outdoor and
multi-train operation, see the LGB
catalog.

Attention!

After extended operation,

this model may leave carbon dust or
other debris around the track. This
dust and debris can stain carpet and
other materials. Consider this when
setting up your layout. Ernst Paul
Lehmann Patentwerk and LGB of
America are not liable for any dam-
ages.

SERVICE

Do-It-Yourself Service Levels

Level

- Beginner

Level

- Intermediate

Level

- Advanced

Attention!

Improper service will void

your warranty. For quality service,
contact your authorized retailer or an
LGB factory service station (see

Authorized Service