background image

afety Information

S

4

Intr

oduction 

Read carefully and thoroughly through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.

This booklet is divided into 2 parts : Warning and Caution.

: This is a warning sign specifying user’s applications which might

be dangerous. 

: This is a sign specifying ‘Strictly Forbidden’ applications.

Warning

: Failure to comply with the instructions under this

sign may result in major physical injuries or death.

Caution

: Failure to comply with the instructions under this

sign may result in minor physical injuries or
damages to the product.

Warning

• Under certain conditions hydrogen gas may be produced in a water heater that has not been

used for two weeks or more. Hydrogen gas can be explosive under these circumstances. 
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.

• The base opening must not be obstructed by carpeting when the washing machine is installed on a

carpeted floor. 

• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.

If the product is exposed to such conditions, electric shock, fire, break down or
deformation may occur.

• Properly ground washer to conform with all governing codes and ordinances. Follow details in

Installation Instructions.

If not grounded properly, break down and leakage of electricity may occur, which may
cause electric shock.

• Must be positioned so that the plug is accessible.

If the plug is placed between the wall and the machine, it may get damaged, possibly
causing fire or electric shock.

• Make sure the plug is completely pushed into the outlet.

Failure to do so may cause electric shock and fire due to overheating.

WATER
HEATER
SAFETY

Caution

PROPER
INSTALLATION

Summary of Contents for WF-T857









































Reviews: