LG WD1208TC4W Owner'S Manual Download Page 39

39

EN

Symptoms

Reason

Solution

Door does not open

Once washing machine has 

started, the door cannot be 

opened for safety reasons.

 

Check if the ‘Door Lock’ icon is 

illuminated. You can safely open the 

door after the ‘Door Lock’ icon turns off.

Wash cycle time 

delayed

If an imbalance is detected or 

if the suds removing feature 

operates, the wash time will 

increase.

 

This is normal. The time remaining 

shown in the display is only an 

estimate. Actual time may vary.

Fabric softener 

overflow

Too much softener may cause 

an overflow.

 

Follow softener guidelines to ensure 

appropriate amount is used. Do not 

exceed the maximum fill line.

Softeners 

dispensed too early

Too much softener may cause 

it to dispense prematurely.

 

Follow the guidelines provided by the 

detergent manufacturer.

 

Close the dispenser drawer slowly. Do 

not open the drawer during the wash 

cycle.

Dry problem

Check water supply tap.

 

Do not overload. Check that the 

washing machine is draining properly to 

extract adequate water from the load. 

Clothes load is too small to tumble 

properly. Add a few towels.

 

Turn off water supply tap.

Odor

This odor is caused by the 

rubber attached to the washing 

machine.

 

It is the normal odor of new rubber and 

will disappear after the machine has 

been run a few times.

If the rubber door gasket and 

door seal area are not cleaned 

regularly, odors can occur from 

mold or foreign substances.

 

Be sure to clean the gasket and door 

seal regularly and check under the door 

seal for small items when unloading the 

washer.

Odors can occur if foreign 

substances are left in the 

drainage pump filter.

 

Be sure to clean the drainage pump 

filter regularly.

Odors can occur if the 

drainage hose is not properly 

installed, causing siphoning 

(water flowing back inside the 

washing machine).

 

When installing the drainage hose, be 

sure that it doesn’t become kinked or 

blocked.

Using the dry function, odors 

can occur from lint and other 

laundry matter sticking to the 

heater. (Dryer model only)

 

This is not a malfunction.

A particular odor can occur 

from drying wet clothes with 

hot air. (Dryer model only)

 

The odor will disappear after a short 

while.

Summary of Contents for WD1208TC4W













































Reviews: