LG UU12 Installation Manual Download Page 17 | Manualshive

Page: 17 / 47

background image

The Indoor Unit Installation

Installation Manual

17

ENGLISH

1) Indoor unit installation

n

Before Installing, prepare Installation Plates

• 'Installation Plates' are attached at the bottom

of indoor unit.
Detach them by removing each 3 screws at
both sides.

• Detach 'Side Plate (R,L)' by removing each 2

screws on both sides.

• Pull the upper right and left side of 'Inlet Grille'

to the front, and it will stop at slightly tilted
position.

• Unhook the 'Inlet hanger' from the 'Hanger

screw' on the both left and right side.

• Detach the 'Inlet Grille' from the Indoor Unit.

1) Installation on the ceiling

• Measure and mark the position for the

Suspension bolts and the piping hole.

• Drill the hole for anchor nut on the ceiling.

※

Before secure the Installation Plates,
select the bent direction of the
Installion Plate to the inside or the
outside according to the installation
circumstances.

• Drill the piping hole on the wall slightly tilted

to the outdoor side using a ø70 hole-core
drill.

1076

Suspension

bolt

Center-line for the

piping hole

265

1236

265

Install Plate

1)

2)

5~7mm

Indoor

Outdoor

WALL

Side Plate

Inlet Grille

Inlet hanger

Hanger

screw

«
...
15
16
17
18
19
...
»

Summary of Contents for UU12
















































Reviews:

No comments

Related manuals for UU12

Room Air Conditioner

Brand: Napoleon Pages: 30

Brand: Vax Pages: 7

Brand: Vax Pages: 12

Brand: Levoit Pages: 12

Brand: Gree Pages: 21

Brand: TCL Pages: 33

Brand: GE Pages: 48

CO2 Conveni-Pack

Brand: Daikin Pages: 80

Brand: Electra Pages: 151

Brand: Airwell Pages: 71

Brand: Hisense Pages: 51

Brand: Toyotomi Pages: 48

Brand: Xpelair Pages: 5

Brand: Seifert Pages: 23

Brand: AeonAir Pages: 36

Brand: Comfee Pages: 130

Brand: REMKO Pages: 16

Brand: OION Technologies Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands