LG TWFB-R101D Manual Download Page 9

Copyrightⓒ. 2015. All Rights Reserved. 

3. Regulation Information 

 
INFORMATION TO THE USER 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures: 
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
- Consult the dealer or an experienced radio/ TV technician for help. 
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) This device must accept any interference received, including interference that may cause undesired operation. 
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could 
void user’s authority to operate the equipment. 
This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. 
A minimum separation distance of 20 ㎝ must be maintained between the antenna and the person for this appliance to satisfy the 
RF exposure requirements. 

8 / 12 

Summary of Contents for TWFB-R101D














Reviews: