background image

Owner's Manual 

3

Safety Precautions

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed.

Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by
the following indications.

Meanings of symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage.

Be sure not to do.

Be sure to follow the instruction.

Always use a power plug and socket with
a ground terminal. 

• There is a risk of electric shock.

Do not use a defective or underrated
circuit breaker. Use the correctly rated
breaker and fuse. 

• There is risk of fire or electric shock .

Do not use a multi consent. Always use
this appliance on a dedicated circuit
breaker.

• Otherwise it can cause electric shock or fire.

For electrical work, contact the dealer, seller,
a qualified electrician, or an Authorized
Service Center. Do not disassemble or repair
the product by yourself.

• There is risk of fire or electric shock.

Always ground the product as per the
wiring diagram. Do not connect the
ground wire to gas or water pipes
lightening rod or telephone ground wire.

• There is risk of fire or electric shock.

Install the panel and the cover of control
box securely. 

• There is risk of fire or electric shock due to

dust , water etc.

Use the correctly rated breaker or fuse. 

• There is risk of fire or electric shock.

Do not modify or extend the power cable.
If the power cable or cord has scrathes or
skin peeled off or deteriorated then it
must be replaced.

• There is risk of fire or electric shock.

For installation, removal or reinstall ,
always contact the dealer or an
Authorized Service Center.

• There is risk of fire, electric shock, explosion, 

or injury.

Do not install the product on a defective
installation stand. Be sure that  the
installation area does not deteriorate with
age. 

• It may cause product to fall. 

Never install the outdoor unit  on a
moving base  or a place from  where  it
can fall down.

• The falling outdoor unit can cause damage or

injury or even death of a person.

When the product is soaked (flooded or
submerged) in water , contact an
Authorized Service Center for repair
before using it again.

• There is risk of fire or eletric shock.

In outdoor unit the step-up capacitor
supplies high voltage electricity to the
electrical components. Be sure to
discharge the capacitor completely
before conducting the repair work.

• An charged capacitor can cause electrical

shock.

When installing the unit, use the
installation kit provided with the product.

• Otherwise the unit may fall and cause severe

injury.

Be sure to use only those  parts which
are  listed in the svc  parts list. Never
attempt to modify the equipment. 

• The use of inappropriate parts can cause an

electrical shock, excessive heat generation or
fire.

Summary of Contents for T182 SCO Series
























Reviews: