LG SP8YA Service Manual Download Page 18

Page: 18 / 75

1-17

Only for training and service purposes.

SPECIFICATIONS

• GENERAL

Power consumption

Refer to the main label on the unit.

AC adapter

Model: DA-50F25

Manufacturer : Asian Power Devices Inc.

Input: 100 - 240 V ~ 50 - 60 Hz

Output: 25 V 2 A

Dimensions (W x H x D)

Approx. 1060.0 mm x 57.0 mm x 119.0 mm (with foot)

(41.7 inch x 2.2 inch x 4.7 inch)

Operating temperature

5 °C to 35 °C (41 °F to 95 °F)

Operating humidity

5 % to 90 %

Bus Power Supply (USB)

5 V 500 mA

Available Digital Input Audio Sampling Frequency 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 192 KHz

Available Digital Input Audio format

Dolby Atmos, Dolby Audio, DTS:X, DTS-HD, PCM

• INPUT/OUTPUT

OPTICAL IN

3 V (p-p), Optical jack x 1

HDMI IN

19 Pin (Type A, HDMI™ connector) x 1

HDMI OUT

19 Pin (Type A, HDMI™ connector) x 1

1080p, 1080i, 720p, 576p, 480p

2160p@24/25/30 Hz 4:4:4

2160p@60/50 Hz 4:2:0

4K Sources dependent on HDCP 2.2 are supported at 4K resolutions.

• AMPLIFIER (RMS Output)

Total

440 W RMS

Front

40 W RMS x 2 (4

at 1 kHz, THD 10 %)

Center

40 W RMS (4

at 1 kHz, THD 10 %)

Top

50 W RMS x 2 (4

at 1 kHz, THD 10 %)

Subwoofer

220 W RMS (3

at 80 Hz, THD 10 %)

• WIRELESS SUBWOOFER

Power requirements

Refer to the main label on the subwoofer.

Power consumption

Refer to the main label on the subwoofer.

Type

1 Way 1 Speaker

Impedance

Rated Input Power

220 W RMS

Max. Input Power

440 W RMS

Dimensions (W x H x D)

Approx. 221.0 mm x 390.0 mm x 312.8 mm

(8.7 inch x 15.4 inch x 12.3 inch)

• SYSTEM

Wireless LAN (Internal antenna)

802.11a/b/g/n Wi-Fi networks

SPK8-S (SPK8-S, S78S1-S), Sold Separately

• WIRELESS RECEIVER

Power requirements

Refer to the main label on the wireless receiver.

Power consumption

Refer to the main label on the wireless receiver.

Rear

70 W RMS x 2 (3

at 1 kHz, THD 10 %)

Dimensions (W x H x D)

Approx. 60.0 mm x 220.0 mm x 175.0 mm

(2.4 inch x 8.7 inch x 6.9 inch)

• REAR SPEAKERS (Each)

Type

1 Way 1 Speaker

Impedance

Rated Input Power

70 W RMS

Max. Input Power

140 W RMS

Dimensions (W x H x D)

Approx. 100.0 mm x 140.0 mm x 100.0 mm

(3.9 inch x 5.5 inch x 3.9 inch)

•

Designs and specifications are subject to change without prior notice.

Summary of Contents for SP8YA



































































Search results

Summary of Contents for SP8YA

Reviews:

Related manuals for SP8YA

Brands by name

Popular brands

LG SP8YA, Service Manual

Search results

Summary of Contents for SP8YA

Reviews:

Related manuals for SP8YA

Brands by name

Popular brands