LG Panorama LFX21980ST Service Manual Download Page 36

Page: 36 / 51

• The resistance of the SENSOR has a ±5% common difference.

TEMPERATURE

RESISTANCE OF FREEZER/Icing

RESISTANCE OF REFRIGERATOR &

SENSOR

DEFROST SENSOR & ROOM SENSOR

- 20 ºC (-4 °F)

22.3 K?

77 K?

- 15 °C (5°F)

16.9 K ?

60 K?

- 10 °C (14 °F)

13.0 K?

47.3 K?

- 5 °C (23 °F)

10.1 K?

38.4 K?

0 °C (32 °F)

7.8 K?

30 K?

+ 5 °C (41 °F)

6.2 K?

24.1 K?

+ 10 °C (50 °F)

4.9 K?

19.5 K?

+ 15 °C (59 °F)

3.9 K?

15.9 K?

+ 20 °C (68 °F)

3.1 K?

13 K?

+ 25 °C (77 °F)

2.5 K?

11 K?

+ 30 °C (86 °F)

2.0 K?

8.9 K?

+ 40 °C (104 °F)

1.4 K?

6.2 K?

+ 50 °C (122 °F)

0.8 K?

4.3 K?

“LOCATED ON DISPLAY PCB”

8-2-3 Temperature Sensor Circuit

• Measure the resistance of the SENSOR after leaving it for over 3 minutes in the measuring temperature.

This delay is necessary due to sensor response speed.

- 36 -

Summary of Contents for Panorama LFX21980ST




















































Search results

Summary of Contents for Panorama LFX21980ST

Reviews:

Related manuals for Panorama LFX21980ST

Brands by name

Popular brands

LG Panorama LFX21980ST, Service Manual

Search results

Summary of Contents for Panorama LFX21980ST

Reviews:

Related manuals for Panorama LFX21980ST

Brands by name

Popular brands