manualshive.com logo in svg

LG MS-2645DPA, Service Manual

Share
Download
LG MS-2645DPA Service Manual Download Page 18

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance. 

(Ohm-meter scale: Rx1)
• Between Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 1.4 

Ω

Approx.: 90 

Ω

Less than: 0.1 

Ω

Normal: 

∞

Normal: 

∞

Normal: Less than 1 

Ω

Normal: 

∞

PRIMARY  
TERMINAL

SECONDARY  
TERMINAL

WINDING

FILAMENT

TERMINAL

COMPONENT TEST PROCEDURE

Summary of Contents for MS-2645DPA



































Reviews:

No comments

Brands by name

Popular brands

Load more brands