LG MS-2082B Service Manual Download Page 8

Page: 8 / 35

4-2

OPERATING SEQUENCE

The following is a description of component functions
during oven operation.

1. CANCEL FUNCTION

Touch the pad whenever you need to

cancel an entry or a function currently in use.

The display will either return to the last item entered

or to the clock.

2. QUICK START

3. MICROWAVE COOKING

4. MULTI-STAGE MICROWAVE

COOKING

5. AUTO DEFROST COOKING

6. QUICK DEFROST COOKING

7. CHILD LOCK

This oven has a CHILD LOCK feature

TO SET CHILD LOCK

• Touch the pad

• Touch STOP/CLEAR pad L appear on

the display.

TO CANCEL CHILD LOCK

• Touch the pad

• touch STOP/CLEAR pad L disappears.

8. RUSSIAN COOK

STOP/CLEAR

START

quick start

STOP/CLEAR

1ST STAGE

STOP/CLEAR

AUTO

DEFROST

NUMBER OF

WEIGHT

(kg)

START

STOP/CLEAR

QUICK

DEFROST

STOP/CLEAR

POWER

TIME

STOP/CLEAR

RUSSIAN

COOK

START

STOP/CLEAR

POWER

TIME

START

2ND STAGE

POWER

TIME

START

STOP/CLEAR

Summary of Contents for MS-2082B




































Search results

Summary of Contents for MS-2082B

Reviews:

Related manuals for MS-2082B

Brands by name

Popular brands

LG MS-2082B, Service Manual

Search results

Summary of Contents for MS-2082B

Reviews:

Related manuals for MS-2082B

Brands by name

Popular brands