LG MS-119 Page 19 Service Manual Download | Manualshive

Page: 19 / 36

background image

5-9

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
CAPACITOR

HIGH VOLTAGE
DIODE

NOTE :
Some inexpensive meters
may indicate infinite
resistance in both direction.

Measure the resistance.
(Ohm-meter scale: Rx1000)
• Terminal to terminal.

Measure the resistance.
(Ohm-meter scale: Rx1000)
• Terminal to case.

Measure the continuity (Forward).
(Ohm-meter scale: Rx10000)

Measure the continuity (Reverse).
(Ohm-meter scale: Rx10000)

Normal: Momentarily indicates

several ohms, and
then gradually returns
to infinite.

Normal: Infinite.

Normal: Continuity.
Abnormal: Infinite.

Normal: Infinite.
Abnormal: Continuity.

NOTE: When testing the magnetron, be sure to install the magnetron gasket

in the correct position and be sure that the gasket is in good condition.

Antenna

Gasket

Chassis

Filament

«
...
17
18
19
20
21
...
»

Summary of Contents for MS-119





































Reviews:

No comments

Related manuals for MS-119

Brand: Jenn-Air Pages: 72

Brand: Jenn-Air Pages: 60

Brand: Jenn-Air Pages: 28

Brand: Jenn-Air Pages: 36

Brand: Jenn-Air Pages: 48

Brand: Jenn-Air Pages: 36

Brand: Jenn-Air Pages: 16

Brand: Jenn-Air Pages: 60

Brand: Samsung Pages: 80

Brand: Pro Lite Pages: 8

Brand: Swan Retro Pages: 19

Brand: Kuppersbusch Pages: 87

Brand: Sunbeam Pages: 14

GORENJE BCM547ST

Brand: S+ARCK Pages: 52

ELECTRIC COMBI OVENS

Brand: air-o-steam Pages: 21

Brand: Sammic Pages: 20

Brand: Hyundai Pages: 17

Brand: Euromaid Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands