manualshive.com logo in svg

LG MS-114ML, Service Manual

Share
Download
LG MS-114ML Service Manual Download Page 8

OPERATING SEQUENCE

The following is a description of component functions
during oven operation.

1. SETTING THE CLOCK

ex) To set 4:30, touch number key [4], [3] and [0] 

NOTE: You can set 12 hour clock.

2. CANCEL FUNCTION

Touch the                   pad whenever you need to

cancel an entry or a function currently in use.

The display will either return to the last item entered

or to the clock. 

3. QUICK START

4. MICROWAVE COOKING

5. MULTI-STAGE  MICROWAVE

COOKING

6. AUTO WEIGHT DEFROST COOKING

7. CHILD LOCK

This oven has a CHILD LOCK feature 

• TO SET CHILD LOCK 

• Touch the                  pad

• Touch STOP pad             TRAVADO  appear in   

the display.

•TO CANCEL CHILD LOCK

• Touch the                   pad

• touch STOP pad             TRAVADO  disappears.

8. AUTO COOK

4-2

Stop

Set

clock

Set the

correct time

Stop

Start

Stop

Desired  

auto cook 

category

STOP

STAGE 1

Set

clock

Stop

Stop

Desired

defrost

category

Desired
cooking

weight

Desired

food weight

Start

Start

Start

Stop

Desired

cooking time

Desired

power level

Start

STAGE 2

Stop

Stop

Desired

cooking time

Desired

power level

Desired

cooking time

Desired

power level

Summary of Contents for MS-114ML



























Reviews:

No comments

Brands by name

Popular brands

Load more brands