LG MS-1146SQP Service Manual Download Page 18 | Manualshive

Page: 18 / 33

background image

5-8

COMPONENT TEST PROCEDURE

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

Approx.: 2.13 ±10% ohm
Approx.: 178.19 ±10% ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY
TERMINAL

SECONDARY
TERMINAL

WINDING

FILAMENT

TERMINAL

COMPONENTS TEST

PROCEDURE RESULTS

1. Measure the resistance.

(Ohm-meter scale: Rx1 and Rx100)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

«
...
16
17
18
19
20
...
»

Summary of Contents for MS-1146SQP


































Reviews:

No comments

Related manuals for MS-1146SQP

Brand: Samsung Pages: 80

Brand: NEFF Pages: 44

Brand: IFB Pages: 8

Brand: Daewoo Pages: 20

Brand: Ariston Pages: 42

Brand: ZANKER Pages: 92

Brand: DAEWOO ELECTRONICS Pages: 31

Brand: Smeg Pages: 14

Brand: THOMSON Pages: 66

Brand: Daewoo Pages: 9

Brand: Fagor Pages: 6

Brand: Foster Pages: 8

Brand: EasyLine Pages: 297

Brand: AEG Pages: 32

Brand: AEG Pages: 32

Brand: AEG Pages: 32

Brand: AEG Pages: 36

Brand: AEG Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands