LG MC-766YS Service Manual Download Page 28

Page: 28 / 36

5-18

(TROUBLE 7) Grill

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Heater is not

operating.

Abnormal.

Normal.

Heater.

Thermostat and
relay3.(Grill)

Abnormal.

Malfunction the
thermostat.

Malfunction the
heater.

Replace.

Wire connection.

No continuity.

Open or loosen.

Replace or
connect tightly.

Replace.

1. Lower tempera-

ture the oven.

Abnormal.

Normal.

Heater.

Thermostat and
relay3.(Grill)

Abnormal.

Malfunction the
thermostat.

Malfunction the
heater.

Replace.

(TROUBLE 6) Oven does not cook properly when programmed for the set power level

(Operates properly on HIGH)

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Output is full when

you set lower
power level.

Abnormal.

Disconnect the
wire leads from
relay 2 and check
continuity relay 2.
(Operate the unit)

Defective P.C.B.
assembly.

Replace P.C.B.
assembly.

NOTE:

* Make sure the wore leads correct position.

* When removing the wire leads from parts be sure to grasp the connector not the wires.
* When removing the magnetron, be sure to install the magnetron gasket in the correct position and in

good condition.

Summary of Contents for MC-766YS





































Search results

Summary of Contents for MC-766YS

Reviews:

Related manuals for MC-766YS

Brands by name

Popular brands

LG MC-766YS, Service Manual

Search results

Summary of Contents for MC-766YS

Reviews:

Related manuals for MC-766YS

Brands by name

Popular brands