background image

CAUTION:

of handling the Remote Controller

• Aim at the signal receiver on the wired remote controller so as to operate.
• The remote control signal can be received at a distance of up to about 7m.
• Be sure that there are no obstructions between the remote controller and the signal receptor.
• Do not drop or throw the remote controller.
• Do not place the remote controller in a location exposed to direct sunlight, or near the heating unit, or

any other heat source.

• Block a strong light over the signal receptor with a curtain or etc. so as to prevent the abnormal

operation. (ex:electronic quick start, ELBA, inverter type fluorescent lamp)

h

The wireless remote controller do not operate the vane angle control.(4Way Type)

h

For more details refer to the Wireless Remote Control Accessory manual.

h

The actual product can be different from above contents depending upon model type.

h

The wireless remote controller does not operate When using simultaneous operation system.

NOTE

8

Ceiling Cassette-Type Air Conditioner

Product Introduction

Wireless Remote Controller (Accessory)

This air-conditioner is equipped with wired remote controller basically. But if you want to be available with
wireless remote controller, you pay for it.

PQWRHDF0

Summary of Contents for MB09AHL
































Reviews: