LG MASTER-K10S1 User Manual Download Page 11 | Manualshive

Page: 11 / 12

LG MASTER-K10S1 User Manual Download Page 11

11

MASTER-K10S1

SEND [FUN(159)] : Transmission data from master to slave

RECV [FUN(158)] : Receiving data from slave to master

Instruction Form :

St : Station number of slave PLC to communicate.(This of master PLC is always h1F.)
S1 : Beginning address of word memory device of master PLC in which data to be
   transmitted to slave is stored.
D1 : Beginning address of word memory device of slave PLC in which data to be
   received from master will be stored.
S2 : Beginning address of word memory device of slave PLC in which data to be
   transmitted to master is stored.
D2 : Beginning address of word memory device of master PLC in which data to be
   received from slave will be stored.
n : The number of word data to be transmitted or received.(Hex. or Decimal)

[ SEND St S1 D1 n ]

[ RECV St D2 S2 n ]

•

Instruction

Note

①

When the transmitted data from master PLC is stored to P area of slave directly,

the output data of P area of slave PLC may clear during operation mode of slave PLC
changing(PROGRAM mode

↔

RUN mode) according to PLC operation system.

②

The range of address(D1, S2) of word memory device for slave PLC in the SEND/RECV

can not be exceed that of master PLC.

«
...
9
10
11
12
»

Summary of Contents for MASTER-K10S1













Reviews:

No comments