background image

A

B

NOTE:

Attach curtains to the air conditioner before 

placing the air conditioner in window.

1.

Place the tabbed side of the side curtain in the 

       track on the right-hand side of the air 
       conditioner cabinet. 

A. Tabbed side of side curtain
B. Lock edge side of side curtain

Install Side Curtains

2.

Slide the side curtain down the track until the 

        curtain is aligned with the top and bottom of 
        the air conditioner cabinet. 

3.

Slide the side curtain frame into the top 

       channel on the top of the air conditioner and 
       the track on the bottom of the air conditioner.

4.

Slide the side curtain frame as close to the 

       air conditioner as necessary to lock the side 
       curtain to the frame. 
5.    Repeat above steps for the left-hand side 
       curtain and frame.

B

A

1.    Measure the width of the window opening.

2.    Mark the center line on the inside windowsill.

A. Width of window opening
B. Center line

Prepare the Window for Installation

A

C

D

E

B

3.    Install the window lock bracket behind the inner 
       windowsill,with the short side of Window lock 
       bracket as shown.Use the two(2) wood screws
       31/32” provided.

The window lock bracket helps to hold air 
conditioner securely in place.Be sure to place 
window lock bracket edge flush against back of
inner sill. 

A. Center line
B.

” screws

C. Inner sill

D.

Outer sill

E. Window lock bracket

OUTSIDE

INSIDE

Summary of Contents for LW5012J





















Reviews: