manualshive.com logo in svg

LG LW1100AP Series, User Manual

Share
Download
LG LW1100AP Series User Manual Download Page 39

 

 

 

 

 

 

 

 

 

 
 

Page 39 of 50

 

 

 

In order to upgrade Access Point firmware via Internet, click the 

Internet

 selection 

button. If you know an URL address that supply Access Point’s latest firmware version 

then enter the address in the dialog box. Otherwise click 

Default URL

 button. 

The Default URL addresses LG Electronics Internet homepage that supports latest 

Access Point firmware version. 

 

If you have defined URL address, press 

Start

 button so that the firmware can be 

transferred to your local disk (Program File 

Ò

 LG Electronics 

Ò

 AP Manager). During 

the firmware down load, if there is an error or file transfer failed then an error message 

will be displayed. 

 

 

 

After complete the firmware downloading, the Manager performs Access Point 

firmware upgrade process. This process can be monitored just like as firmware 

download process. 

 

Firmware Upgrade Via Internet 

Summary of Contents for LW1100AP Series



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands