background image

2

This lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of 
sufficient magnitude to constitute a risk of electric
shock to persons. 

The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.

CAUTION: 

The apparatus should not be exposed to water 

(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.

Warning: 

Do not install this equipment in a confined space

such as a bookcase or similar unit. 

Warning:

Wiring methods shall be in accordance with the

National Electric Code, ANSI/NFPA 70.

FCC WARNING:

This equipment may generate or use radio 

frequency energy. Changes or modifications to this equipment
may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose
the authority to operate this equipment if an unauthorized
change or modification is made.

Regulatory Notices For U.S.A 

This equipment has been tested and found to comply with the 
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
• A suitable conduit entries, knock-outs or glands shall be 

provided in the cable entries of this product in the end user.

• Caution: Danger of explosion if battery is incorrectly

replaced.Replaced only with the same or equivalent type 
recommended by the manufacturer. Dispose of used batteries
according to the manufacturer ’s instructions.

• Holes in metal, through which insulated wires pass, shall have

smooth well rounded surfaces or shall be provided with 
brushings.

Warning: 

This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may
be required to take adequate measures.

CAUTION: 

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK 

DO NOT OPEN

LVC-DV321EC_AABBSL1_ENG  5/20/06  9:39 AM  Page 2

Summary of Contents for LVC-DV321EC



















Reviews: