LG LSN5MR3T1 Installation Manual Download | Manualshive

Page: 1 / 22

background image

INSTALLATION MANUAL

AIR CONDITIONER

TYPE : WALL MOUNTED

Please read this installation manual completely before installing the product.
When the power cord is damaged, replacement work shall be
performed by authorized personnel on;y.
Installation work must be performed in accordance with the national wiring
standards by authorized personnel only.
Please retain this installation manual for
future reference after reading it thoroughly.

P/No. MFL39754859

LG Electronics India Pvt. Ltd.

Registered Office

:

A-27, Mohan Co-operative

Industrial Estate, Mathura Road, New Delhi-110044
Tel: 011-26991412, Fax: 011-26991410

www.lg.com

1
2
3
...
»

Summary of Contents for LSN5MR3T1























Reviews:

No comments

Related manuals for LSN5MR3T1

Brand: Omega Altise Pages: 16

Brand: UV CAN SANITIZE Pages: 8

Sleeping Well BACK

Brand: Indel B Pages: 54

Altherma EPGA16DAV3

Brand: Daikin Pages: 100

Brand: Klimaire Pages: 51

Continuous dry verge

Brand: Sandtoft Pages: 2

Brand: Daikin Pages: 32

OmniAire 2000C Series

Brand: Omnitec Pages: 9

Brand: Dimplex Pages: 28

Brand: Olimpia splendid Pages: 40

Brand: Easy@Home Pages: 56

Brand: Airwell Pages: 76

Brand: GE Pages: 32

Brand: OdorStop Pages: 12

Brand: Daikin Pages: 15

Brand: Daikin Pages: 24

Brand: Daikin Pages: 18

Brand: Fellowes Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands