manualshive.com logo in svg

LG LSM4200, Owner'S Manual, Page: 38 / 67

Share
Download
LG LSM4200 Owner'S Manual Download Page 38

37

Specifications        

NOTE

Information in this document is subject to change without notice.

Max. Resolution

RGB : 1920 x 1080 @ 60 Hz 
HDMI/DVI : 1920 x 1080 @ 60 Hz

– It may not be supported 

depending on the OS or video card type.

Recommended Resolution

RGB : 1920 x 1080 @ 60 Hz
HDMI/DVI :  1920 x 1080 @ 60 Hz

– It may not be 

supported depending on the OS or video card type.

Horizontal Frequency

RGB : 30 kHz to 83 kHz
HDMI/DVI : 30 kHz to 83 kHz

Vertical Frequency

RGB : 56 Hz to 75 Hz
HDMI/DVI : 56 Hz to 60 Hz

Synchronization Type

Separate/Composite/Digital

15-pin 

D-Sub

type, HDMI (digital), S-Video, 

Composite Video, Component, RS-232C

Operational Condition

Temperature: 0 ˚C to 40 ˚C , Humidity: 10 % to 80 % 

Storage Condition

Temperature: -20 ˚C to 60 ˚C , Humidity: 5 % to 90 % 

Video Signal

Input Connector

Environmental
Conditions

The product specifications can change without prior notice for product improvement.

RMS Audio Output

10 W + 10 W (R + L)

Input Sensitivity

0.7 Vrms

Speaker Impedance

8 

Ω

Audio

* Applicable only for models that support the speakers 

Summary of Contents for LSM4200




































































Reviews:

No comments