LG LSHD3080ST Service Manual Download Page 12 | Manualshive

Page: 12 / 35

background image

-12-

PLANNING THE INSTALLATION

ELECTRICAL

For personal safety, remove house fuse or open

circuit breaker before beginning installation. Do not

use extension cord or adapter plug with this

appliance.

Follow national electrical codes or prevailing

local codes and ordinances.
Electrical Supply:
This appliance requires a 120V 60Hz electrical

supply, and connected to an individual, properly

grounded branch circuit, protected by a 15 or 20

ampere circuit breaker or time delay fuse. Wiring

must be 2 wire w/ ground. Please also refer Electrical

Diagram labeled on product.

Cable Lock:
A cable locking connector (not supplied) might also

be required by local codes. Check with local

requirements and codes, purchase and install

appropriate connector if necessary.

Cable Lock

WARNING

All Electrical work must by performed by

qualified electrician or person with similar

technical know how and background.

WARNING

Electrical wiring must be done by a qualified

person(s) in accordance with all applicable

codes and standards. This range hood must

be properly grounded. Turn off electrical

power at service entrance before wiring.

«
...
10
11
12
13
14
...
»

Summary of Contents for LSHD3080ST




































Reviews:

No comments

Related manuals for LSHD3080ST

Brand: AIRFORCE Pages: 94

STRATUS NB Series

Brand: Faber Pages: 104

Brand: KOBE Pages: 66

Brand: Wolf Pages: 16

INCA SMARTINSP28SS400

Brand: Faber Pages: 68

Brand: Caple Pages: 24

Brand: KitchenAid Pages: 16

Brand: KitchenAid Pages: 2

Brand: KitchenAid Pages: 6

Brand: KitchenAid Pages: 36

Brand: KitchenAid Pages: 28

Brand: KitchenAid Pages: 32

Brand: KitchenAid Pages: 2

Brand: KitchenAid Pages: 28

Brand: KitchenAid Pages: 28

LI3ZFF/W10321799G

Brand: KitchenAid Pages: 32

Brand: KitchenAid Pages: 28

Pro-Line KICV167RMT0

Brand: KitchenAid Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands