background image

2

Safety Precautions

Operating Instructions

Care and Maintenance

Troubleshooting Tips

WARNING

WARNING

WARNING

WARNING

CAUTION

CAUTION

WARNING

WARNING

Safety precautions

Safety Precautions

Warning ................................2

Caution .................................3

Operating Instructions

Preparation before operation ..4

Remote Control Features .....5

Operation Mode Selection ......7

Additional features ..............13

Care and Maintenance

Care and Maintenance .......16

Operation Tips ....................18

Troubleshooting tips

Before You 
Call For Service 
...............19

To prevent injury to the user or other people and property damage, the
following instructions must be followed.

Incorrect operation due to ignoring of instruction will cause harm or
damage, the seriousness is classified by the following indications.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to
properties only.

Plug in the power plug
properly.

• Otherwise, it will cause

electrical shock or fire due to
heat generation.

Do not operate or stop the
unit by inserting or pulling
out the power plug.

• It will cause electrical shock

or fire due to heat
generation.

Do not damage or use an
unspecified power cord.

• It will cause electrical shock or fire.

• If the supply cord is damaged, it

must be replaced by the
manufacturer or its service agent
or a similarly qualified person in
order to avoid a hazard.

Do not modify power cord

length or share the outlet

with other appliances.

• It will cause electrical shock

or fire due to heat
generation.

Do not operate with wet
hand.

• It may cause electrical

shock.

Do not insert anything into the
air inlet/air outlet.

• Since the fan rotates at high

speed, this may cause an
injury or damage the unit.

Do not expose the skin
directly to cool air for long
periods of time.

• This could damage your

health.

When an abnormality (smell of burning, etc)
occurs, stop the air conditioner, and disconnect
the power plug or turn off the breaker.

• If the unit continues to be operated

in an abnormal condition, it may
cause a fire, damage, etc. In this
case, consult your dealer.

Repair or relocation should
not be done by the
customer.

• If this is done incorrectly, it may

cause a fire, electric shock, injury
by dropping of the unit, water
leakage, etc. Consult your dealer.

■ 

Do not install, remove and reinstall the unit by yourself.

• Improper installation will cause water leakage, electrical

shock, or fire. Please consult authorized dealer or specialist
for the installation work. Please note fault caused by
improper installation is not covered by warranty.

• Unit must be installed in an easily accessible area. Any

additional cost required to hire a special equipment to
service the unit will be the responsibility of the customer.

Installation precautions

Summary of Contents for LS-K2464HL





















Reviews: