LG LP126HD3B Svc Manual Download | Manualshive

Page: 6 / 49

background image

- 6 -

Copyright ©2010 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

1.3 SELF-DIAGNOSIS

FUNCTION:

If the unit has a malfunction, a green OPERATION LED located on the Display PCB used by the unit to
indicate the

fault codes

.

USE:

If the customer has to register a complaint to the service center, he can be very clear about registering
the complaint that what is happening & by referring the user's manual the customer can clearly define
the problem.
So that the engineer should go fully prepared with the prescribed tools to be used regarding that
problem. It also keeps the customer aware about the unit.
Here are some of the problems defined below for which the LED indicates by flashing.
The

fault codes

are the mentioned which is as follows:

•

Electrical Controls

•

Overheating Protection

This feature prevents melting of unit by electrical heater located inside of the unit at the remote
mode (when the unit is connected with wall thermostat). LED on the control panel displays
"OP"

•

Freeze Protection

This feature prevents freezing of room at low temperature.
LED on the control panel displays "FP"

NOTICE

ON

Normal

OFF

No power / failed board

Fault Codes

CH 01

Indoor Air Thermistor Error

CH 02

Indoor Coil Thermistor Error

CH 07

Themostat Wiring Error

CH 09

EEPROM Check Sum Error

CH 10

Indoor Fan Error

CH 34

High Pressure Switch Error

CH 44

Outdoor Air Thermistor Error (PTHP Only)

CH 45

Outdoor Coil Thermistor Error (PTHP Only)

CH 67

Outdoor Fan Error

«
...
4
5
6
7
8
...
»

Summary of Contents for LP126HD3B


















































Reviews:

No comments

Related manuals for LP126HD3B

Brand: Fellowes Pages: 32

Brand: Olimpia splendid Pages: 154

Brand: Olimpia splendid Pages: 26

Brand: Olimpia splendid Pages: 100

Brand: Olimpia splendid Pages: 44

Brand: Olimpia splendid Pages: 80

Brand: Argo Pages: 38

Optimum YW09H2/I

Brand: Yamato Pages: 15

Brand: Iwata Pages: 6

Brand: B.Pro Pages: 24

Brand: DeLonghi Pages: 4

EL16XC1-036-230A01

Brand: Lennox Pages: 108

Brand: Daikin Pages: 140

Brand: Pure n Natural Systems Pages: 4

Brand: Midea Pages: 15

Brand: Nordyne Pages: 20

Brand: Mitsubishi Pages: 23

Brand: Lennox Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands