- 26 -
Copyright ©2010 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
7. Remove the screw that attaches the electric heater wire to
the side of the indoor fan housing.
8. Remove the 3 screws which fasten the top cover assembly.
9. Position water spraying plastic tube into the electric heater
cover. Make sure that the three pairs(total of six) of plastic
tongues snap into the corresponding metal slots of the
heater frame as shown in Figure 27. Then install one of the
three rubber elbows(ref. Figure 31.) at the inlet of the
spraying tube and through the rubber grommet.
10. Place the top cover assembly back into the unit.
11. Install tube #1 and tube #2 (ref. Figure 31.) on the pump
assembly using the rubber elbows as shown in Figure 28.
12. Position pump assembly to the basepan as shown in
Figure 29. and fasten the pump bracket to the basepan
using the three screws provided.
13. Insert tube #2 of the pump assembly through the plastic
grommet of the sheet metal partition as shown in Figure 30.
Then connect the end of tube #2 to the plastic elbow
coming out of the inlet of the spraying tube.
Installation
7. Remove the screw that attaches the
electric heater wire to the side of
the indoor fan housing.
8. Remove the 3 screws which fasten
the top cover assembly.
9. Position water spraying plastic
tube into the electric heater cover.
Make sure that the three pairs(total
of six) of plastic tongues snap into
the corresponding metal slots of
the heater frame as shown in fig. 4.
Then install one of the three rubber
elbows(ref. fig. 8) at the inlet of the
spraying tube and through the
rubber grommet.
10. Place the top cover assembly
back into the unit.
11. Install tube #1 and tube #2
(ref. fig. 8) on the pump assembly
using the rubber elbows as
shown in fig. 5.
12. Position pump assembly to the
basepan as shown in fig. 6 and
fasten the pump bracket to the
basepan using the three screws
provided.
13. Insert tube #2 of the pump
assembly through the plastic
grommet of the sheet metal
partition as shown in fig. 7.
Then connect the end of tube #2
to the plastic elbow coming out of
the inlet of the spraying tube.
14. Connect the condensate pump to
the ICR relay of the terminal of the
board as shown in fig. 9 Make
sure to fasten the pump wire
through the wire clip on the back
side of the control barrier as
shown in fig. 10
15. Assembly the unit back following
the reverse order of disassembly.
NOTE:
All tube should be inserted
into rubber elbows by at least 1/2 inch
Figure 26
Figure 27
Figure 28
Figure 30
Figure 31
Figure 29
For more information contact
your local district office or
www.lgusa.com
Figure 33
Figure 32
Pump
assembly
Tube #1
Tube #2
Rubber
elbows(3)
Spraying
Tube
3828A20274B
BL
BL
Installation
7. Remove the screw that attaches the
electric heater wire to the side of
the indoor fan housing.
8. Remove the 3 screws which fasten
the top cover assembly.
9. Position water spraying plastic
tube into the electric heater cover.
Make sure that the three pairs(total
of six) of plastic tongues snap into
the corresponding metal slots of
the heater frame as shown in fig. 4.
Then install one of the three rubber
elbows(ref. fig. 8) at the inlet of the
spraying tube and through the
rubber grommet.
10. Place the top cover assembly
back into the unit.
11. Install tube #1 and tube #2
(ref. fig. 8) on the pump assembly
using the rubber elbows as
shown in fig. 5.
12. Position pump assembly to the
basepan as shown in fig. 6 and
fasten the pump bracket to the
basepan using the three screws
provided.
13. Insert tube #2 of the pump
assembly through the plastic
grommet of the sheet metal
partition as shown in fig. 7.
Then connect the end of tube #2
to the plastic elbow coming out of
the inlet of the spraying tube.
14. Connect the condensate pump to
the ICR relay of the terminal of the
board as shown in fig. 9 Make
sure to fasten the pump wire
through the wire clip on the back
side of the control barrier as
shown in fig. 10
15. Assembly the unit back following
the reverse order of disassembly.
NOTE:
All tube should be inserted
into rubber elbows by at least 1/2 inch
Figure 26
Figure 27
Figure 28
Figure 30
Figure 31
Figure 29
For more information contact
your local district office or
www.lgusa.com
Figure 33
Figure 32
Pump
assembly
Tube #1
Tube #2
Rubber
elbows(3)
Spraying
Tube
3828A20274B
BL
BL
Installation
7. Remove the screw that attaches the
electric heater wire to the side of
the indoor fan housing.
8. Remove the 3 screws which fasten
the top cover assembly.
9. Position water spraying plastic
tube into the electric heater cover.
Make sure that the three pairs(total
of six) of plastic tongues snap into
the corresponding metal slots of
the heater frame as shown in fig. 4.
Then install one of the three rubber
elbows(ref. fig. 8) at the inlet of the
spraying tube and through the
rubber grommet.
10. Place the top cover assembly
back into the unit.
11. Install tube #1 and tube #2
(ref. fig. 8) on the pump assembly
using the rubber elbows as
shown in fig. 5.
12. Position pump assembly to the
basepan as shown in fig. 6 and
fasten the pump bracket to the
basepan using the three screws
provided.
13. Insert tube #2 of the pump
assembly through the plastic
grommet of the sheet metal
partition as shown in fig. 7.
Then connect the end of tube #2
to the plastic elbow coming out of
the inlet of the spraying tube.
14. Connect the condensate pump to
the ICR relay of the terminal of the
board as shown in fig. 9 Make
sure to fasten the pump wire
through the wire clip on the back
side of the control barrier as
shown in fig. 10
15. Assembly the unit back following
the reverse order of disassembly.
NOTE:
All tube should be inserted
into rubber elbows by at least 1/2 inch
Figure 26
Figure 27
Figure 28
Figure 30
Figure 31
Figure 29
For more information contact
your local district office or
www.lgusa.com
Figure 33
Figure 32
Pump
assembly
Tube #1
Tube #2
Rubber
elbows(3)
Spraying
Tube
3828A20274B
BL
BL
Installation
7. Remove the screw that attaches the
electric heater wire to the side of
the indoor fan housing.
8. Remove the 3 screws which fasten
the top cover assembly.
9. Position water spraying plastic
tube into the electric heater cover.
Make sure that the three pairs(total
of six) of plastic tongues snap into
the corresponding metal slots of
the heater frame as shown in fig. 4.
Then install one of the three rubber
elbows(ref. fig. 8) at the inlet of the
spraying tube and through the
rubber grommet.
10. Place the top cover assembly
back into the unit.
11. Install tube #1 and tube #2
(ref. fig. 8) on the pump assembly
using the rubber elbows as
shown in fig. 5.
12. Position pump assembly to the
basepan as shown in fig. 6 and
fasten the pump bracket to the
basepan using the three screws
provided.
13. Insert tube #2 of the pump
assembly through the plastic
grommet of the sheet metal
partition as shown in fig. 7.
Then connect the end of tube #2
to the plastic elbow coming out of
the inlet of the spraying tube.
14. Connect the condensate pump to
the ICR relay of the terminal of the
board as shown in fig. 9 Make
sure to fasten the pump wire
through the wire clip on the back
side of the control barrier as
shown in fig. 10
15. Assembly the unit back following
the reverse order of disassembly.
NOTE:
All tube should be inserted
into rubber elbows by at least 1/2 inch
Figure 26
Figure 27
Figure 28
Figure 30
Figure 31
Figure 29
For more information contact
your local district office or
www.lgusa.com
Figure 33
Figure 32
Pump
assembly
Tube #1
Tube #2
Rubber
elbows(3)
Spraying
Tube
3828A20274B
BL
BL
Installation
7. Remove the screw that attaches the
electric heater wire to the side of
the indoor fan housing.
8. Remove the 3 screws which fasten
the top cover assembly.
9. Position water spraying plastic
tube into the electric heater cover.
Make sure that the three pairs(total
of six) of plastic tongues snap into
the corresponding metal slots of
the heater frame as shown in fig. 4.
Then install one of the three rubber
elbows(ref. fig. 8) at the inlet of the
spraying tube and through the
rubber grommet.
10. Place the top cover assembly
back into the unit.
11. Install tube #1 and tube #2
(ref. fig. 8) on the pump assembly
using the rubber elbows as
shown in fig. 5.
12. Position pump assembly to the
basepan as shown in fig. 6 and
fasten the pump bracket to the
basepan using the three screws
provided.
13. Insert tube #2 of the pump
assembly through the plastic
grommet of the sheet metal
partition as shown in fig. 7.
Then connect the end of tube #2
to the plastic elbow coming out of
the inlet of the spraying tube.
14. Connect the condensate pump to
the ICR relay of the terminal of the
board as shown in fig. 9 Make
sure to fasten the pump wire
through the wire clip on the back
side of the control barrier as
shown in fig. 10
15. Assembly the unit back following
the reverse order of disassembly.
NOTE:
All tube should be inserted
into rubber elbows by at least 1/2 inch
Figure 26
Figure 27
Figure 28
Figure 30
Figure 31
Figure 29
For more information contact
your local district office or
www.lgusa.com
Figure 33
Figure 32
Pump
assembly
Tube #1
Tube #2
Rubber
elbows(3)
Spraying
Tube
3828A20274B
BL
BL
Summary of Contents for LP096CD3A
Page 49: ...P NO MFL63264608 JANUARY 2010 ...
