manualshive.com logo in svg

LG LMV2053SB - 2.0 Cu. Ft. Microwave, Service Manual

Share
Download
LG LMV2053SB - 2.0 Cu. Ft. Microwave Service Manual Download Page 27

7-16

COMPONENTS

TEST RESULTS

Normal:
Momentarily indicates
several ohms, and then
gradually returns to infinite
Normal: Infinite.

Normal: Continuity.
Abnormal: Infinite.

Normal: Infinite.
Abnormal: Continuity.

1. Remove wire leads.
2. Measure resistance. (ohm meter scale: Rx1000)

• Terminal to terminal

• Terminal to case

1. Measure continuity. Forward.

(ohm meter scale: Rx1000)

2. Measure continuity. Reverse.

(ohm meter scale: Rx1000)

CAPACITOR

DIODE

Some inexpensive ohm
meters may indicate infinite
resistance in both directions.

1. Measure continuity.

(ohm meter scale: Rx1)

2. Remove the lead wires and operate  oven at

power level 1 through power level 10.

RELAY 7

1. Remove wire leads.

2. Measure resistance.

(ohm meter scale: Rx1)

Normal: Approximately
Terminal            : 35 to 50 ohms
Terminal            : 5 to 15 ohms
Abnormal:
Infinite or several.

A

B

C

FAN MOTOR

A

C

A

B

Power

Level

Open

Close

1
2
3
4
5
6
7
8
9

10

4 Sec
6 Sec
8 Sec

10 Sec
12 Sec
14 Sec
16 Sec
18 Sec
20 Sec
22 Sec

18 Sec
16 Sec
14 Sec
12 Sec
10 Sec

8 Sec
6 Sec
4 Sec
2 Sec
0 Sec

Summary of Contents for LMV2053SB - 2.0 Cu. Ft. Microwave













































Reviews:

No comments

Brands by name

Popular brands

Load more brands