LG LG A1C-A5 Series Installation Manual Download Page 99

Page: 99 / 107

AC Module System Installation Manual

Rev. 1.0

9 Product Specifications

DC Input

Parameter

Section

LG355A1C-A5

LG360A1C-A5

LG365A1C-A5

Power

Max.

355W

360W

365W

Tolerance

0% ~ 3%

Voltage

Voc

42.7V

42.8V

Vmpp

36.3V

36.5V

36.7V

Tolerance

–5% ~ +5%

Current

Isc

10.78A

10.79A

10.80A

Impp

9.79A

9.87A

9.95A

Tolerance

–5% ~ +5%

Note : PV module was measured at STC (Standard Test Condition: Irradiation 1,000W/m

, Cell temp. 25℃(77℉),1.5AM)

AC Output

Parameter

Section

240VAC

208VAC

Power

Inverter Rated Continuous

320W

Voltage

Nominal(Range)

240V (211V ~ 264V)

208V (183V ~ 229V)

Current

Nominal Output

1.33A

1.54A

Frequency

Nominal(Range)

60Hz (59.3Hz ~ 60.5Hz)

Power Factor(adjustable)

1/0.8 leading…0.8 lagging

CEC Weighted Efficiency

(California Energy Commission)

97%

96%

Max. Number of AC Modules

12 EA

10 EA

Certification

DC module

UL1703, IEC61215, IEC 61730, Safety Class II

AC module

UL1741, IEEE1547, UL1741SA

FCC Part 15 Class B

IEEE 1547 (Default)

Parameter

Range

Clearing Time (s)

Phase Voltage

V < 50%

0.16

50% ≤ V < 88%

2.00

110% ≤ V < 120%

1.00

V ≥ 120%

0.16

Frequency

> 60.5 Hz

0.16

< 59.3 Hz

0.16

•

After the micro inverter got tripped by voltage or frequency abnormality, it takes about 5 min for the AC module
to operate.

•

If it got tripped by other reasons or it is connected with the utility after sunrise, it takes about 1 min for the AC
module to operate.

1) Refer to 3-12 Connecting Array of AC Modules to Distribution Panel regarding Maximum number of AC Modules.

9-1 AC module , LGXXXA1C-A5

Summary of Contents for LG A1C-A5 Series











































































































Search results

Summary of Contents for LG A1C-A5 Series

Reviews:

Related manuals for LG A1C-A5 Series

Brands by name

Popular brands

LG LG A1C-A5 Series, Installation Manual

Search results

Summary of Contents for LG A1C-A5 Series

Reviews:

Related manuals for LG A1C-A5 Series

Brands by name

Popular brands