manualshive.com logo in svg

LG LFC21770ST - Panorama - 0.7 cu. ft, User'S Manual & Installation Instructions

Share
Download
LG LFC21770ST - Panorama - 0.7 cu. ft User'S Manual & Installation Instructions Download Page 16

REFRIGERATOR INSTALLATION

16

2. Replacing Refrigerator Door

❿

Right Door

• Lower the door onto the middle hinge pin (6).

• Make sure the door is aligned with the

cabinet.

• Replace the top hinge (5) by rotating the lever

hinge (4) counter clockwise to secure it.

• Make sure the gasket on the door is flush

against the cabinet and is not folded.

• Support the door on the handle side while

securing. And make sure the door is straight
and the gap between the doors is even
across the front.

• Install the ground screw (3) and connect the

wire harness (2).

• Tighten the cover screw (1).

❿

Left Door

• Replace the left door followed by the same

way described above.

• When replacing the top hinge (5), rotate the

lever hinge (4) clockwise at this time.

: Be careful of missing the

washer [part(7)]. Because it can be easily
taken off.

6

6

7

7

CAUTION

Summary of Contents for LFC21770ST - Panorama - 0.7 cu. ft







































Reviews:

No comments

Brands by name

Popular brands

Load more brands