LG LFC20740 Series Owner'S Manual Download Page 34

Page: 34 / 36

TROUBLESHOOTING GUIDE

ICE HAS OFF-TASTE OR ODOR

The icemaker was recently installed.

Discard first few batches of ice to avoid discolored or
off-flavored ice.

The ice has been stored for too long.

Throw away old ice and make new supply.

The food has not been wrapped tightly in

Rewrap foods since odors may migrate to the ice if food

either compartment.

is not wrapped properly.

The water supply contains minerals such as sulfur.

A filter may need to be installed to eliminate taste and

odor problems.

The interior of refrigerator needs cleaning.

See

Care and Cleaning

section.

Ice storage bin needs cleaning.

Empty and wash bin. Discard old cubes.

THERE IS WATER IN THE DEFROST DRAIN PAN

The refrigerator is defrosting.

The water will evaporate. It is normal for water to drip into the
defrost pan.

It is more humid than normal.

Expect that the water in the defrost pan will take longer to

evaporate. This is normal when it is hot or humid.

THE REFRIGERATOR SEEMS TO MAKE TOO MUCH NOISE

The sounds may be normal for your refrigerator.

Refer to the

Understanding Sounds You May Hear section.

THE ICEMAKER IS NOT PRODUCING ICE OR ICE CUBES ARE FREEZING TOO SLOWLY

The freezer temperature is cold enough to produce ice. Wait 24 hours after hook-up for ice production. See the

Setting

the Controls

Section.

Door left open.

Check to see if something is holding the door open.

THE DOORS ARE DIFFICULT TO OPEN

The gaskets are dirty or sticky.

Clean gaskets and the surfaces that they touch. Rub a thin

coat of appliance polish or kitchen wax on the gaskets after
cleaning

The door is reopened within a short time after having

When you open the door, warmer air enters the refrigerator.

been opened.

As the warm air cools, it can create a vacuum. If the door is

hard to open, wait 5 minutes to allow the air pressure to
equalize, then see if it opens more easily.

CUBES PRODUCED BY ICEMAKER ARE TOO SMALL

Smaller cube size level is selected.

Select larger cube size using cube size selector.

Water shutoff valve connecting refrigerator to water

Call a plumber to clear the valve.

line may be clogged.

Check if...

Then...

Check if...

Then...

Check if...

Then...

Check if...

Then...

Check if...

Then...

Check if...

Then...

Summary of Contents for LFC20740 Series





































Search results

Summary of Contents for LFC20740 Series

Reviews:

Related manuals for LFC20740 Series

Brands by name

Popular brands

LG LFC20740 Series, Owner'S Manual

Search results

Summary of Contents for LFC20740 Series

Reviews:

Related manuals for LFC20740 Series

Brands by name

Popular brands