LG L705i Service Manual Download Page 19

Page: 19 / 196

LGE Internal Use Only

Only for training and service purposes

The GSM900, DCS, and PCS receiver inputs of RTR6275 are connected directly to the transceiver

frontend circuits(filters and antenna switch module). GSM900, DCS, and PCS receiver inputs are

similar to the RFR6275 UMTS Rx input in that they also use differential configurations to improve

common-mode rejection

Since GSM900, DCS, and PCS signals are time-division duplex (the handset can only receive or

transmit at one time), switches are used to separate Rx and Tx and second-order non-linearity

performance. The balance between the complementary signals is critical and must be maintained from

the RF filter outputs all the way into the IC pins

signals in place of frequency duplexers - this is accomplished in the switch module.

The GSM900, DCS, and PCS receive signals are routed to the RTR6275 through band selection filters

and matching networks that transform single-ended 50-Ω •sources to differential impedances optimized

for gain and noise figure. Similar to the RFR, the RTR input uses a differential configuration to improve

second-order inter-modulation and common mode rejection performance. The RTR6275 input stages

include MSM-controlled gain adjustments that maximize receiver dynamic range.

The amplifier outputs drive the RF ports of the quadrature RF-to-baseband downconverters. The

downconverted baseband outputs are multiplexed and routed to lowpass filters (one I and one Q)

having passband and stopband characteristics suitable for GMSK or 8-PSK processing. These filter

circuits include DC offset corrections. The filter outputs are buffered and passed on to the MSM6280 IC

for further processing (an interface shared with the RFR6275 UMTS receiver outputs

3. TECHNICAL BRIEF

- 20 -

Switch Mode

CTRL1

CTRL2

CTRL3

GSM850/EGSM TX

PCN/PCS TX

WB850

WB1900

WB2100

GSM850 RX

EGSM RX

PCN RX

PCS RX

All Off

ANENNA SWITCH MODULE LOGIC

Table 3.2.1 Antenna Switch Module Control logic

Z3X-BOX.COM

Summary of Contents for L705i























































































































































































Search results

Summary of Contents for L705i

Reviews:

LG L705i, Service Manual, Page: 19 / 196

Search results

Summary of Contents for L705i

Reviews: