background image

1

FCC Compliance Statement

This equipment has been tested and found to comply within
the limits of a Class B digital device pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.

This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.

If this equipment does cause harmful interference to radio
or television reception (which can be determined by turning
the equipment on and off), the user is encouraged to try to
correct the interference by using one or more of the
following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for  help.

Caution: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user's (or your) authority to operate the equipment. Only
peripherals (digital input/output devices, terminals, printers,
etc.) certified to comply with the Class B limits may be
attached to this monitor. Operation with non-certified
peripherals is likely to result in interference to radio and TV
reception.
Only shielded signal cables may be used with this System.

Canadian DOC Notice

This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.

CE Conformity Notice

(for Europe)

Products with the “CE” Marking comply with the EMC
Directive(89/336/EEC) and LOW VOLTAGE Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compiance with these directives implies conformity to the
following European Norms :
• EN 55022:1998          ; Radio Frequency Interference
• EN 55024:1998  ; Electromagnetic Immunity
• EN 61000-3-2             ; Power Line Harmonics
• EN 61000-3-3             ; Voltage Fluctuations
• EN 60950                    ; Product Safety

Low Radiation Compliance (MPR II)

This monitor meets one of the strictest guidelines available
today for low radiation emissions, offering the user extra
shielding and an antistatic screen coating. These
guidelines, set forth by a government agency in Sweden,
limit the amount of emission allowed in the Extremely Low
Frequency (ELF) and Very Low Frequency (VLF)
electromagnetic range.

TCO95

Congratulations! 
You have just purchased a TCO’95 approved and labelled
product!  Your choice has provided you with a product
developed for professional use.  Your purchase has also
contributed to reducing the burden on the environment and
to the further development of environmentally-adapted
electronic products.

Why do we have environmentally labelled computers? 
In many countries, environmental labelling has become an
established method for encouraging the adaptation of
goods and services to the environment.  The main problem
as far as computers and other electronic equipment are
concerned is that environmentally harmful substances are
used both in the products and during their manufacture.
Since it has not been possible so far for the majority of
electronic equipment to be recycled in a satisfactory way,
most of these potentially damaging substances sooner or
later enter Nature.

There are also other characteristics of a computer, such as
energy consumption levels, that are important from both the
working and natural environment viewpoints.  Since all
types of conventional electricity generation have a negative
effect on the environment (acidic- and climatic-influencing
emissions, radioactive waste, etc.), it is vital to conserve
energy.  Electronic equipment in offices consumes as
enormous amount of energy, since it is often routinely left
running continuously.

What does the environmenal labelling involve?
This product meets the requirements for the TCO’95 

Regulatory Information

NOTICE

The regulations are applied only to the products with the
ID LABEL indicating specific requirements.

NOTICE

The regulations are applied only to the products with the
ID LABEL indicating specific requirements.

NOTICE

The regulations are applied only to the products with the
ID LABEL indicating specific requirements.

Summary of Contents for L15MP
























Reviews: