background image

4

Room Air Conditioner

Safety Precautions

Two or more people must lift and
transport the product. 

• Avoid personal injury. 

Do not install the product where it will be
exposed to sea wind (salt spray) directly.

• It may cause corrosion on the product. 

Install the drain hose to ensure that the
condensed  water is drained away properly. 

• A bad connection may cause water leakage.

Keep level even when installing the
product.

• To avoid vibration or noise.

Do not install the product where the noise
or hot air from the outdoor unit could
damage or  disturb the neighborhoods.

• It may cause a problem for your neighbors

and hence dispute.

Always check for gas (refrigerant)
leakage after installation or repair of
product.

• Low refrigerant levels may cause failure of

product.

Indoor/outdoor wiring connections must  be
secured tightly and the cable should be routed
properly so that there is no force pulling the
cable from the connection terminals.

• Improper or loose connections can cause

heat  generation or fire.

Safely dispose off the packing materials. Like
screws, nails, batteries, broken things etc
after installation or svc and then tear away
and thraw away the plastic packaging bags.

• Children may play with them and cause

injury.

Make sure to check that the power cable
plug is not dirty, loose or broken  and
then only insert the plug completely.

• Dirty, loose or broken power plug can

cause electric shock or fire.

Be sure to check the refrigerant to the
used. Please read the label on the product.

• Incorrect refrigerant used can prevent the

normal operation of the unit.

Don't use a power cord, a plug  or a loose
socket which is damaged.

• Otherwise it  may cause a fire or electrical

shock.

Do not touch , operate, or repair  the
product with wet hands. Hold the plug by
hand when taking out 

• There is risk of electric shock  or fire.

Do not place a heater or other heating
appliances near the power cable.

• There is risk of fire and electric shock.

Do not allow water to run into electric parts.
Install the unit away from water sources.

• There is risk of fire, failure of the product, or

electric shock.

Do not store or use or even allow flammable
gas or combustibles near the product. 

• There is risk of fire.

Do not use the product in a tightly closed
space for a long time. Perform ventilation
regularly.

• Oxygen deficiency could occur and hence

harm your health.

Do not open the front  grille of the product
during operation. (Do not touch the
electrostatic filter, if the unit is so equipped.) 

• There is risk of physical injury, electric shock,

or product failure.

If strange sounds, smell or smoke comes
from product.Immediately turn the breaker
off or disconnect the power supply cable.

• There is risk of electric shock or fire.

Ventilate the product room  from time to
time when operating it together with a
stove, or heating element etc.

• Oxygen deficiency can occur and hence harm

your health.

Turn the main power off and unplug the
unit when cleaning or repairing the
product. 

• There is risk of electric shock.

When the product is not to  be used for a
long time, disconnect the power supply
plug or turn off the breaker.

• There is risk of product damage or failure, or

unintended operation.

Take care to ensure that nobody especially
kids could step on or fall onto the outdoor unit. 

• This could result in personal injury and

product damage. 

Take care to ensure that power cable could not
be pulled out or damaged during operation.

• There is risk of fire or electric shock.

Do not place ANYTHING  on the power
cable.

• There is risk of fire or electric shock.

Do not plug or unplug the power supply
plug to turn the unit ON/OFF .

• There is risk of fire or electric shock.

When flammable gas leaks, turn off the
gas and open a window for ventilation
before turn the product on. 

• Do not use the telephone or turn switches on

or off. There is risk of explosion or fire.

For inner cleaning, contact an Authorized
Service Center or a dealer. 
Do not use harsh detergent that causes
corrosion or damage on the unit.

• Harsh detergent may also cause failure of

product, fire, or electronic shock.

Summary of Contents for G09LH




















Reviews: