LG F14U2TDH0N Service Manual Download

Page: 12 / 54

5. OPERATION

How to use washer

Power

Touch and release your fingers to turn it

on.

Program dial

Programs are available according to the

laundry type.

Lamp will light up to indicate selected

program.

LED display

The display shows the settings, estimated

time remaining, options, and status
messages for your washer.

The display will remain on through the

cycle.

Start/Pause

This Start/Pause button is used to start

wash cycle or pause the wash cycle.

If temporary stop of wash cycle is

needed, touch the Start/Pause button.

When in Pause, the power is turned off

automatically after 4 minutes.

Options

This allows you to select an additional

cycle and will light when selected.

Use thise buttons to select the desired

cycle options for the selected cycle.

Control panel

Start/Pause Button

Power Button

LED display

SmartDiagnosis™ function is
available only for the products with
a SmartDiagnosis™ mark.

Program dial

Options

Summary of Contents for F14U2TDH0N























































Search results

Summary of Contents for F14U2TDH0N

Reviews:

Related manuals for F14U2TDH0N

Brands by name

Popular brands

LG F14U2TDH0N, Service Manual

Search results

Summary of Contents for F14U2TDH0N

Reviews:

Related manuals for F14U2TDH0N

Brands by name

Popular brands