background image

27

roubleshooting guide

This washing machine is equipped with automatic safety functions which detect and
diagnose faults at an early stage and react appropriately.
When the machine does not function properly or does not function at all, check the
following points before you contact your service provider. 

Symptom

Possible Cause

Solution

Rattling and 
clanking noise

Thumping sound

Vibrating noise

Water leaks.

Oversudsing

Water does not enter
washer or it enters
slowly

Water in the washer
does not drain or
drains slowly.

• Foreign objects such as coins or

safety pins maybe in drum or
pump.

• Heavy wash loads may produce

a thumping sound. This is usually
normal.

• Have all the transit bolts and

packing been removed?

• Are all the feet resting firmly on

the ground?

• Fill hoses or drain hose are loose

at tap or washer.

• House drain pipes are clogged.

• Water supply is not adequate in

area.

• Water supply tap is not

completely open.

• Water inlet hose(s) are kinked.

• The filter of the inlet hose(s) are

clogged.

• Drain hose is kinked or clogged.

• The drain filter is clogged.

Stop washer and check drum
and drain filter.
If noise continues after washer
is restarted,  call your authorized
service centre.

If sound continues, washer is 
probably out of balance. Stop and
redistribute wash load.

If not removed during
installation, refer to Installation guide   
for removing transit bolts. 
Wash load may be unevenly
distributed
in drum. Stop washer and 
rearrange wash load.

Check and tighten hose connections.

Unclog drain pipe. Contact plumber
if necessary.

Too much detergent or unsuitable 
detergent may cause excessive 
foaming which may result in water 
leaks.

Check another tap in the house.

Fully open tap.

Straighten hose(s).

Check the filter of the inlet hose(s).

Clean and straighten the drain hose.

Clean the drain filter.

T

Summary of Contents for F1407TDS

































Reviews: