background image

Industry Canada Statement   

This device complies with Industry Canada’s applicable licence-exempt RSSs. Operation is subject to the 

following two conditions: 

(1) This device may not cause interference; and 

(2) This device must accept any interference, including interference that may cause undesired operation 

of the device. 

 

Avis d’Industrie Canada 

Cet appareil est conforme aux normes CNR d’Industrie Canada applicables aux appareils radio exempts 

de licence. Son 

fonctionnement est sujet aux deux conditions suivantes : 

1) Cet appareil ne doit pas provoquer d’interférences, et 

2) Cet appareil doit accepter toutes les interférences, y compris celles pouvant entraîner son 

dysfonctionnement. 

 

IC Radiation Exposure Statement 

This equipment complies with IC radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with 

a minimum distance of

 20 cm (7.8 

inches) between the antenna 

and

 your body. 

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY 

UNAUTHORIZED  MODIFICATIONS  TO  THIS  EQUIPMENT.  SUCH  MODIFICATIONS  COULD  VOID  THE 

USER’S AUTHORITY TO OPERATE THE EQUIPMENT. 

 

Avis d’Industrie Canada sur l’exposition aux rayonnements 

Cet  appareil  est  conforme  aux  limites  d’exposition  aux  rayonnements  d’Industrie  Canada  pour  un 

environnement non contrôlé. Cet appareil doit être installé de façon à garder une distance minimale de 

20 cm (7,8 po) entre la source de rayonnement et votre corps. 

REMARQUE : LE FABRICANT N’EST PAS RESPONSABLE DES INTERFÉRENCES 

RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES APPORTÉES À CET APPAREIL. 

DE TELLES MODIFICATIONS POURRAIENT ANNULER L’AUTORISATION ACCORDÉE À L’UTILISATEUR DE 

FAIRE FONCTIONNER L’APPAREIL. 

 

Summary of Contents for EBR81777301








Reviews: