LG CodePlus HCS6300 Series Installation & Setup Manual Warranty Download | Manualshive

Page: 11 / 52

background image

206-4122

11

Installing a CodePlus Feature Card

Note: The CodePlus series products are NOT designed to be hot-swappable!!! Power

must be removed to the card frame before any CodePlus transcoder cards are inserted

or removed.
Note: All cards used in the card frame must be inserted and removed by qualified

service personnel only.
Note: Use extreme care when handling an HCS6300 card. Always observe proper

precautions with respect to static electricity and mechanical shock. When not installed

in a card frame, return the HCS6300 card to the anti-static bag in which it was shipped.
Note: The card slots in the card frame are NOT all identical!!! An HCS6300 card can only

be installed in the CONTROLLER slot. The connector arrangement of Slots 1 to 6 and 7

to 12 is incompatible with the HCS6300.
Note: When installing cards, remove blank cover plates and insert new cards as appli-

cable. For ports that will not be used, leave the blank cover plates in place for proper

ventilation and FCC and safety agency compliance.

Refer to the diagram on page 12, and follow the procedure below to install the CodePlus

feature card.
1. Unpack the HCS6300 unit and the supplied HCS6400 fan card.

Note:

If you are installing the HCS6300 in an HCS6150R card frame, an HCS6400

fan card is pre-installed in Slot 7. In this case, the HCS6400 fan card shipped with the

HCS6300 is a spare.

2. Remove the AC power cord for the card frame from the power outlet.
3. Prepare the CONTROLLER slot in the card frame by removing either the blank cover plate

or the CodePlus card currently in the slot. If installing in an HCS6100R card frame, also

prepare Slot 7 for the HCS6400 fan card.

4.

Without using force

, slide the HCS6300 card into the CONTROLLER slot, and ensure that

it is fully inserted. If applicable, then slide the HCS6400 fan card into Slot 7, and ensure

that it is fully inserted.

5. Engage and tighten the top and bottom thumbscrews of the card(s) securely. Note that the

thumbscrews should only be finger tight; overtightening may damage the assembly.

6. Refer to the diagram on page 13 for cabling connections, and complete the HCS6300 system

installation procedure on page 14.

«
...
9
10
11
12
13
...
»

Summary of Contents for CodePlus HCS6300 Series





















































Reviews:

No comments

Related manuals for CodePlus HCS6300 Series

Brand: Nautel Pages: 23

Brand: Nautel Pages: 66

Brand: RKI Instruments Pages: 65

Brand: Comtek Pages: 18

FiberLink 4160 Series

Brand: Artel Pages: 12

Brand: ZyXEL Communications Pages: 1

Brand: Itm Pages: 50

PowerTalk Head w/ADSP & SNS 04-22

Brand: SGC Pages: 72

Brand: Stageline Pages: 25

Brand: OrangeRx Pages: 24

Brand: GE Pages: 4

Brand: GE Pages: 7

Ericsson MASTR II

Brand: GE Pages: 6

Brand: GE Pages: 32

Brand: GE Pages: 3

Hart Druck RTX 1000H Series

Brand: GE Pages: 40

Masoneilan 12410

Brand: GE Pages: 80

Brand: GE Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands