manualshive.com logo in svg

LG C1100, Service Manual, Page: 109 / 127

Share
Download
LG C1100 Service Manual Download Page 109

- 108 -

10.1  BB Test [MENU 1]

Baseband Test

10.1.1  LCD

• Contrast value : This menu is to test Main LCD contrast.

- Contrast Value [10-50] : Change this value by up and down key.

• Sub LCD Contrast : This menu is to test Sub LCD contrast.

- Contrast Value [0-50] : Change this value by up and down key.

10.1.2  Backlight [1-2]

This menu is to test the LCD Backlight and Keypad Backlight.

• Backlight On 

: LCD Backlight and Keypad Backlight light on at the same time.

• Backlight Off 

: LCD Backlight and Keypad Backlight light off at the same time.

• Backlight value 

: This controls brightness of Backlight. When entering into the menu,

the present backlight-value in the phone is displayed. Use Left / Right
key to adjust the level of brightness. The value of the brightness set at
last will be saved in the NVRAM.

10.1.3  Buzzer 

This menu is to test the melody sound.

• Melody on 

: Melody sound is played through the speaker.

• Melody off 

: Melody sound is off.

10.1.4  Vibrator

This menu is to test the vibration mode.

• Vibrator On 

: Vibration mode is on.

• Vibrator Off 

: Vibration mode is off.

10.1.5  ADC (Analog to Digital Converter)

This displays the value of each ADC.

• MVBAT ADC (Main Voltage Battery ADC)

• AUX ADC (Auxiliary ADC) 

• TEMPER ADC (Temperature ADC) 

10.1.6  BATTERY

• Bat Cal  :

This displays the value of Battery Calibration. 
The following menus are displayed in order; BAT_LEV_4V, BAT_LEV_3_LIMIT,
BAT_LEV_2_LIMIT, BAT_LEV_1_LIMIT, BAT_IDLE_LI MIT, BAT_INCALL_LIMIT,
SHUT_DOWN_VOLTAGE, BAT_RECHARGE_LMT

• TEMP Cal :

This displays the value of Temperature Calibration.
The following menus are displayed in order; TEMP_HIGH_LIMIT,
TEMP_HIGH_RECHARGE_LMT, TEMP_LOW_RECHARGE_LMT, TEMP_LOW_LIMIT

10. ENGINEERING MODE

Summary of Contents for C1100
































































































































Reviews:

No comments