LG AVUQ60GM2A0 Installation Manual Download Page 6

Page: 6 / 25

INSTALLATION OF OUTDOOR UNIT

ENGLISH

- If an awning is built over the unit to prevent direct sunlight or rain exposure, make sure that

heat radiation from the condenser is not restricted.

- Ensure that the spaces indicated by arrows around front, back and side of the unit.

- Do not place animals and plants in the path of the warm air.

- Take the air conditioner weight into account and select a place where noise and vibration are

minimum.

- Select a place so that the warm air and noise from the air conditioner do not disturb neighbors.

More than

300 mm

Fence or

obstacles

More than

300 mm

More than

300 mm

Sunr

oof

More than 700 mm

More than 600 mm

Unit : mm

Installation Places

MODEL

CAPACITY

Pipe Size

Length A (m)

Elevation B (m)

Additional

Refrigerant

(g/m)

Gas

Liquid

Standard

Max.

Standard

Max.

AVUQ60GM2A0

17 kW

Ø 19,05(3/4) Ø 9,52(3/8)

7,5

Piping length and the elevation

INSTALLATION OF OUTDOOR UNIT

Ceiling Suspended Air conditioner

Summary of Contents for AVUQ60GM2A0


























Search results

Summary of Contents for AVUQ60GM2A0

Reviews:

Related manuals for AVUQ60GM2A0

Brands by name

Popular brands

LG AVUQ60GM2A0, Installation Manual

Search results

Summary of Contents for AVUQ60GM2A0

Reviews:

Related manuals for AVUQ60GM2A0

Brands by name

Popular brands