LG AVNQ36GM2T1 Installation Manual Download Page 21

Page: 21 / 24

ENGLISH

INSTALLATION INSTRUCTIONS

Installer Setting - Checking Address of Central Control

1. With the FUNC. button pressed, press the RESET button.

2. Press the ON/OFF button toward the indoor unit 1 time, and the indoor unit will display the set

address in the display window.

• The address display time and method can differ by the indoor unit type.

3. Reset the remote controller to use the general operation mode.

1. With the MODE button pressed, press the

RESET button.

2. By using the temperature setting button, set

the indoor unit address.

• Setting range : 00 ~ FF

3. After setting the address, press the ON/OFF

button toward the indoor unit 1 time.

4. The indoor unit will display the set address to

complete the address setting.

• The address display time and method can

differ by the indoor uint type.

5. Reset the remote controller to use the general

operation mode.

°C/°F (5 s)

TIME (3 s)

Installer Setting - Setting Address of Central Control

1,MFL70699801,영어 2018. 6. 27. 오후 4:07 페이지 21

Summary of Contents for AVNQ36GM2T1

























Search results

Summary of Contents for AVNQ36GM2T1

Reviews:

Related manuals for AVNQ36GM2T1

Brands by name

Popular brands

LG AVNQ36GM2T1, Installation Manual

Search results

Summary of Contents for AVNQ36GM2T1

Reviews:

Related manuals for AVNQ36GM2T1

Brands by name

Popular brands