background image

6

INSTALLATION PLACES

ENGLISH

INSTALLATION PLACES

Outdoor unit

- If an awning is built over the unit to prevent

direct sunlight or rain exposure, make sure
that heat radiation from the condenser is not
restricted.

- Ensure that the spaces indicated by arrows

around front, back and side of the unit.

- Do not place animals and plants in the path

of the warm air.

- Take the air conditioner weight into account

and select a place where noise and vibration
are minimum.

- Select a place so that the warm air and noise

from the air conditioner do not disturb neigh-
bors.

More than

3

00

More than 700

More than 600

More than

More than

3

00

3

00

Sunroof

Fence or

obstacles

OUTDOOR

OU

TD

OO

R

Unit

Unit

OUTDOOR

Unit

More than

3

00

Unit : mm

PIPING LENGTH AND THE ELEVATION

If installed tube is shorter than 10 m, additional charging is not necessary. 

*Additional Refrigerant = ((A) -10) x Additional refrigerant (g) 

Single Operation

Outdoor unit

Indoor unit

A

B

Outdoor unit

Indoor unit

A

B

Model Name 

Pipe Size (mm(inch)) 

Length 'A' (m) 

Elevation 'B' (m)  Additional

refrigerant

(g/m)

Gas 

Liquid 

Min. Max. Min. Max. 

AUUQ18GH0 Ø12.7(1/2) Ø6.35(1/4)  7.5

50

5

30

20

AUUQ21GH0 Ø12.7(1/2) Ø6.35(1/4)  7.5

50

5

30

20 

AUUQ24GH0 Ø15.88(5/8) Ø9.52(3/8)  7.5

50

5

30

20

AUUQ36GH0 Ø15.88(5/8) Ø9.52(3/8)  7.5

50

5

30

20

Summary of Contents for AUUQ18GH0




















Reviews: