LG ARWN Series Installation Manual Download Page 51

Page: 51 / 75

Electrical Wiring

1. Use a separate power supply for the Outside Unit and Indoor Unit.

2. Bear in mind ambient conditions (ambient temperature,direct sunlight, rain water,etc.) when proceed-

ing with the wiring and connections.

3. The wire size is the minimum value for metal conduit wiring. The power cord size should be 1 rank

thicker taking into account the line voltage drops. Make sure the power-supply voltage does not drop
more than 10%.

4. Specific wiring requirements should adhere to the wiring regulations of the region.

5. Power supply cords of parts of appliances for outside use should not be lighter than polychloroprene

sheathed flexible cord.

6. Do not install an individual switch or electrical outlet to disconnect each of indoor unit separately from

the power supply.

Wiring of Main Power Supply and Equipment Capacity

• Follow ordinance of your governmental organization for technical standard related to electrical equipment, wiring reg-

ulations and guidance of each electric power company.

• Make sure to use specified wires for connections so that no external force is imparted to terminal connections. If con-

nections are not fixed firmly, it may cause heating or fire.

• Make sure to use the appropriate type of overcurrent protection switch. Note that generated overcurrent may include

some amount of direct current.

• Some installation site may require attachment of an earth leakage breaker. If no earth leakage breaker is installed, it may

cause an electric shock.

• Do not use anything other than breaker and fuse with correct capacity. Using fuse and wire or copper wire with too large

capacity may cause a malfunction of unit or fire.

Installation Manual

ENGLISH

Summary of Contents for ARWN Series












































































Search results

Summary of Contents for ARWN Series

Reviews:

Related manuals for ARWN Series

Brands by name

Popular brands

LG ARWN Series, Installation Manual

Search results

Summary of Contents for ARWN Series

Reviews:

Related manuals for ARWN Series

Brands by name

Popular brands