background image

Installation Manual  

5

Safety Precautions

ENGLISH

Operation

Do not modify or extend the
power cable.

• There is risk of fire or electric

shock.

Do not let the air conditioner
run for a long time when the
humidity is very high and a
door or a window is left open.

• Moisture may condense and

wet or damage furniture.

Be cautious when unpacking
and installing  the product.

• Sharp edges could cause in-

jury. Be especially careful of
the case edges and the fins
on the condenser and evapo-
rator.

For installation, always con-
tact the dealer or an Autho-
rized Service Center.

• There is risk of fire, electric

shock, explosion, or injury.

Do not install the product on
a defective installation stand.

• It may cause injury, accident,

or damage to the product.

Be sure the installation area
does not deteriorate with age.

• If the base collapses, the air

conditioner could fall with it,
causing property damage,
product failure, and personal
injury.

Do not store or use flammable gas or combustibles near the product.

• There is risk of fire or failure of product.

Use a vacuum pump or Inert (nitrogen) gas when do leakage test or air purge. Do not compress air
or Oxygen and do not use Flammable gases. Otherwise, it may cause fire or explosion. 

• There is the risk of death, injury, fire or explosion.

Summary of Contents for ARNU48GBRZ2
































Reviews: