LG ARNU12GSF14 Installation Manual Download Page 10 | Manualshive

Page: 10 / 27

background image

10

Indoor Unit

Installation

Read completely, then follow step by step.

CAUTION

Do not install the product where it could be exposed to sea wind (salty wind) directly.
It can result corrosion on the product.

!

• Do not have any heat or steam near the unit.
• Select a place where there are no obstacles in front of the unit.
• Make sure that condensation drainage can be conveniently routed away.

Do not install near a doorway.

• Ensure that the space around the left and right of the unit is more than 50 cm. The unit should be installed as high on the

wall as possible, allowing a minimum of 10 cm from ceiling.

• Use a stud finder to locate studs to prevent unnecessary damage to the wall.

Features

Signal Receptor

Front Panel

Air Discharge

Air Filter

Plasma Filter

More than 200 mm (Minimum)

More

than 500 mm

More than 1.5 m

More

than 500 mm

Selection of the best location

Installation

«
...
8
9
10
11
12
...
»

Summary of Contents for ARNU12GSF14




























Reviews:

No comments

Related manuals for ARNU12GSF14

EPFX HEPA375VSC

Brand: EnviroPureFX Pages: 4

Brand: Sakura Pages: 20

Brand: Zodiac Pages: 18

Brand: teca Pages: 11

Altherma EPGA16DAV3

Brand: Daikin Pages: 100

Brand: Klimaire Pages: 51

Brand: Daikin Pages: 57

Multi-Tech 2000

Brand: Surround Air Pages: 8

Brand: Napoleon Pages: 27

Brand: Crosley Pages: 9

Brand: Villara Pages: 16

Brand: Carrier Pages: 13

Brand: Lennox Pages: 14

Brand: Crosley Pages: 8

Brand: Celuplast Pages: 8

Liebert CRV Plus

Brand: Vertiv Pages: 98

Brand: Daikin Pages: 88

Brand: ICP Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands