background image

Installation Manual  

9

ENGLISH

Installation

Ceiling dimension and hanging bolt location

Level gauge

Ceiling

Ceiling board

Unit:mm(inch)

570(22-7/16) Unit size

570(22-7/16) Unit size

450(17-1

1/16) 

(Hanging bolt)

75(3)

75(3)

600(23-5/8) (Ceiling opening)

600(23-5/8) (Ceiling opening)

521(20-1/2)(Hanging bolt) 

39.5(1-9/16)

39.5(1-9/16)

TE Chassis

TQ/TR Chassis

TM/TN/TP Chassis

Unit:mm(inch)

Unit:mm(inch)

875(34-7/16) (Ceiling opening)

787(30-15/16)

(Hanging bolt)

bolt)

684(26-15/16)(Hanging bolt)

671(26-7/16)

875(34-7/16) (Ceiling opening)

840(33-1/16) 

Unit size

840(33-1/16) 

Unit size

585~660(20-3/8~26)(Ceiling opening)

517(23)

461(18-1/8)

517(23)

585~660(20-3/8~26)

(Ceiling opening)

523(20-9/16)

570(22-7/16)

570(22-7/16)

319(12-9/16)31

9(1

2-9

/16

)

319(12-9/16)

• The dimensions of the paper model for installation are the same as those of the ceiling opening dimensions.

• Avoid the following installation location.
1. Such places as restaurants and kitchen where considerable amount of oil steam and flour is generated.

These may cause heat exchange efficiency reduction, or water drops, drain pump mal-function.
In these cases, take the following actions;

• Make sure that ventilation fan is enough to cover all noxious gases from this place.
• Ensure enough distance from the cooking room to install the air conditioner in such a place where it may

not suck oily steam.

2. Avoid installng air conditioner in such

places where cooking oil or iron powder is
generated.

3. Avoid places where inflammable gas is

generated.

4. Avoid place where noxious gas is 

generated.

5. Avoid places near high frequency 

generators.

CAUTION :

• This air-conditioner uses a drain

pump.

•  Install the unit horizontally using a

level gauge.

• During the installation, care should be

taken not to damage electric wires.

• Select and mark the position for fixing bolts and piping hole.
• Decide the position for fixing bolts slightly tilted to the drain

direction after considering the direction of drain hose.

• Drill the hole for anchor bolt on the wall.

Use the ventilation fan
for smoke-collecting
hood with sufficient
capacity.

Cooking table

Air conditioner

Take enough
distance

Summary of Contents for ARNU093TRC2
























Reviews: