background image

ENGLISH

9

 CAUTION

Viewing environment

•  Viewing Distance

y

-

Maintain a distance of at least twice the screen diagonal 

length when watching 3D contents. If you feel discomfort in 

viewing 3D contents, move further away from the TV.

Viewing age

•  Infants/Children

y

-

Usage/ Viewing 3D contents for children under the age of 5 

are prohibited.

y

-

Children under the age of 10 may overreact and become 

overly excited because their vision is in development (for 

example: trying to touch the screen or trying to jump into it.) 

Special monitoring and extra attention is required for children 

watching 3D contents. 

y

-

Children have greater binocular disparity of 3D presentations 

than adults because the distance between the eyes is 

shorter than that of adults. Therefore they will perceive more 

stereoscopic depth compared to adults for the same 3D 

image.

•  Teenagers

y

-

Teenagers under the age of 19 may react with sensitivity 

due to stimulation from light in 3D contents. Advise them 

to refrain from watching 3D contents for a long time when 

they are tired.

•  Elderly

y

-

The elderly may perceive less 3D effect compared to the 

young. Do not sit closer to the TV than the recommended 

distance.

Cautions when using the 3D glasses

•  Make sure to use LG 3D glasses. Otherwise, you may not be able to 

view 3D videos properly.

•  Do not use 3D glasses instead of your normal glasses, sunglasses or 

protective goggles.

•  Using modified 3D glasses may cause eye strain or image 

distortion.

•  Do not keep your 3D glasses in extremely high or low 

temperatures. It will cause deformation.

•  The 3D glasses are fragile and are easily scratched. Always use a 

soft, clean piece of cloth when wiping the lenses. Do not scratch 
the lenses of the 3D glasses with sharp objects or clean/wipe them 
with chemicals.

Preparing

 NOTE

•  If the TV is turned on for the first time after it was shipped from the 

factory, initialization of the TV may take a few minutes.

•  Image shown may differ from your TV.
•  Your TV’s OSD (On Screen Display) may differ slightly from that 

shown in this manual.

•  The available menus and options may differ from the input source 

or product model that you are using.

•  New features may be added to this TV in the future.
•  The TV can be placed in standby mode in order to reduce the power 

consumption. And the TV should be turned off if it will not be 
watched for some time, as this will reduce energy consumption.

•  The energy consumed during use can be significantly reduced if the 

level of brightness of the picture is reduced, and this will reduce 
the overall running cost.

•  The items supplied with your product may vary depending on the 

model.

•  Product specifications or contents of this manual may be changed 

without prior notice due to upgrade of product functions.

•  For an optimal connection, HDMI cables and USB devices should 

have bezels less than 10 mm thick and 18 mm width. Use an 
extension cable that supports USB 2.0 if the USB cable or USB 
memory stick does not fit into your TV’s USB port. 

A

B

A

B

    

*A 

<

=

 10 mm

*B 

<

=

 18 mm

 

•  Use a certified cable with the HDMI logo attached. 
•  If you do not use a certified HDMI

 

cable, the screen may not display 

or a connection error may occur. (Recommended HDMI

 

Cable Types) 

- High-Speed HDMI

®

/

TM

 Cable (3m or less) 

- High-Speed HDMI

®

/

TM

 Cable with Ethernet (3m or less)

 CAUTION

•  Do not use any unapproved items to ensure the safety and product 

life span.

•  Any damage or injuries caused by using unapproved items are not 

covered by the manufacturer’s warranty.

•  Some models have a thin film attached on to the screen and this 

must not be removed.

•  Do not remove the panel with your fingers or any tools. Doing so 

may damage the product. (Only UF84**)

Summary of Contents for 65UH600T

































Reviews: