LG 62SX4R, Service Manual

Page: 23 / 51

- 23 -
10. Screen Position Adjustment
: Base value ( H : 0, V : 0)
1) Required Test Equipment
A remote control of adjustment
2) Horizontal Position Adjustment
(1) Press ADJ key on the remote control to enter the
adjustment mode
(2) Select the POSITION of the adjustment menu.
(3) As shown this , adjustment Pattern is displayed.
(4) Adjust data with using the left/right key on the remote
control in order to be left/right symmetry screen<Fig 7>.
(5) When the changeable range is escaped, you do NG.
3) Vertical Position Adjustment
(1) Change the data to symmetrized upper and down of
screen (refer to Fig 8) and then press the Volume key
on Remote control to get out of adjustment mode.
(2) When the changeable range is escaped, you do NG.
* After finishing the adjustment, input the EU 0.5ch to check
the adjustment level.
11. Adjusting the Auto Color Balance
1) Required Test Equipment
: Remote Control, MSPG-925FS Pattern Generator
(NTSC 720p YpbPr output & PC 1024*768@60Hz with
Standard(0.7Vpp) Vertical 100% Color Bar Pattern &
Vertical16 Gray Pattern)
2) Preparation for Adjustment
(1) Connect power and turn Power on.
(2) Do Heat-Run for 5 minutes and over before adjustment.
(3) Receive the component1.
(4) Receive the NTSC, COLOR Bar Pattern of MSPG-
925FS <Fig 9>.
3) Adjusting the Auto Color Balance
1) On inputting the signal, press the ADJ key on the remote
control to enter the adjustment mode when screen is
displayed.
2) In adjustment items, enter the Auto RGB(HEX) and press
the (
G
)button to enter the adjustment items, auto,atonally
In menus, enter the Auto Color Balance
G
To Set and
press the button to complete and then display the “OK”
OSD message.
3) When AV1 adjustment is completed, turn to the
Component1.
4) Press Adjust key on the remote control to enter the
adjustment mode after receive the 720/60Hz Pattern,
COLOR Bar Pattern of MSPG-925FS <Fig 9>.
5) In adjustment items, enter the Auto RGB(HEX) and press
the (
G
)button to enter the adjustment items, auto,atonally
In menus, enter the Auto Color Balance
G
To Set and
press the button to complete and then display the “OK”
OSD message.
6) When Component adjustment is completed, turn to the
RGB.
7) Press Adjust key on the remote control to enter the
adjustment mode after receive the 720/60Hz Pattern,
COLOR Bar Pattern of MSPG-925FS <Fig10>.
8) In adjustment items, enter the Auto RGB(HEX) and press
the (
G
)button to enter the adjustment items, auto,atonally
In menus, enter the Auto Color Balance
G
To Set and
press the button to complete and then display the “OK”
OSD message.
** Passively, correct the Sub Picture(HUDSON)**
If Vertical 16 Gray Pattern is shaked. after finishing the
adjustment.
- When green color is appear, severely.
a. In menu, press the to enter the Hudson at the Device.
b. In menu, passively correct, coming down the ADC G-
Offset2.
c. Press the ADJ button to exit the adjustment mode.
- When green color is appear, lightly.
a. In menu, press the to enter the Hudson at the Device.
b. In menu, passively correct, coming up the ADC G-
Offset2.
c. Press the ADJ button to exit the adjustment mode.
12. Adjusting the Actuator
1) Required Test Equipment
: Remote Control
2) Preparation for Adjustment
(1) Connect a power source with TV Set and turn TV set on.
(2) Using the Service Remote Control, enter from ADJ to
Actuator_60Hz.
<Fig 9. COLOR BAR Pattern> <Fig 10. Vertical16 Gray Pattern>
A
B
<Fig 8>EU 05ch
<Fig 7>