LG 49SM5KD Service Manual Download Page 6

Page: 6 / 46

- 6 -

Only training and service purposes.

SPECIFICATION

No.

Item

Specification

Remarks

Supported Sync. Type

Separate Sync, Digital

Operating Frequency

Analog

Horizontal

30 ~ 83 kHz

Vertical

56 ~ 75 Hz

Digital

Horizontal

30 ~ 83 kHz

Vertical

56 ~ 60 Hz (DVI-D,OPS)
30Hz,56 ~ 60Hz (HDMI1/2,DP)

Resolution

Analog

Max

1920×1080 @ 60Hz(RGB/DVI/OPS)

3840x2160@30Hz(HDMI1/2,DP)

Recommend 1920×1080 @ 60Hz

Digital

Max

1920×1080 @ 60Hz(RGB/DVI/OPS)

3840x2160@30Hz(HDMI1/2,DP)

Recommend 1920×1080 @ 60Hz

3.1. RGB, DVI-D, HDMI, Display Port (PC) Specification

1. Application range

This specification is applied to the LW79A chassis.

2. Test Specification

Each part is tested as below without special appointment.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F),

CST: 40 °C ± 5 °C

2) Relative Humidity: 65 % ± 10 %

3) Power Voltage

: Standard input voltage (100-240 V~, 50/60 Hz)

* Standard Voltage of each products is marked by models.

4) Specification and performance of each parts are followed

each drawing and specification by part number in accord

ance with BOM.

5) The receiver must be operated for about 20 minutes prior to

the adjustment.

3. General Specification

Summary of Contents for 49SM5KD














































Search results

Summary of Contents for 49SM5KD

Reviews:

Related manuals for 49SM5KD

Brands by name

Popular brands

LG 49SM5KD, Service Manual

Search results

Summary of Contents for 49SM5KD

Reviews:

Related manuals for 49SM5KD

Brands by name

Popular brands