background image

- 6 -

LGE Internal Use Only

Copyright  © 

  LG Electronics. Inc. All rights reserved.

Only for training and service purposes

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range

This specification is applied to the LED TV used LA68H 

chassis.

2. Requirement for Test

Each part is tested as below without special appointment.

(1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C

(2) Relative Humidity: 65 % ± 10 %

(3) Power Voltage

: Standard input voltage (AC 100-240 V~, 50/60 Hz)

* Standard Voltage of each products is marked by models.

(4)  Specification and performance of each parts are followed 

each drawing and specification by part number in 

accordance with BOM.

(5)  The receiver must be operated for about 5 minutes prior to 

the adjustment.

3. Test method

(1) Performance: LGE TV test method followed 

(2) Demanded other specification 

- Safety : CE, IEC specification

- EMC : CE, IEC  

4. Model General Specification

No.

Item

Specification

Remarks

1

Receiving System

ATSC / NTSC-M / 64 QAM / 256 QAM

2

Available Channel

1) VHF : 02~13

2) UHF : 14~69

3) DTV : 02-69

4) CATV : 01~135

5) CADTV : 01~135

3

Input Voltage

AC 110V, 60HZ

Mark : 110V, 60Hz (N.America)

4

Market

North America

5

Screen Size

43/49 inch Wide (1920 × 1080)

FHD / 60Hz

43LF5400-UE

49LF5400-UE

40 inch Wide (1920 × 1080)

FHD / 60Hz

40LH5300-UA

6

Aspect Ratio

16:9

7

Tuning System

FS

8

Module

Direct

NC430EUN-AACR1

LGD

FHD / 60Hz

43LF5400-UE

NC490EUN-AACR1

LGD

49LF5400-UE

NC400DUE-VXCP3

INX

40LH5300-UA

9

Operating Environment

1) Temp   :  0 ~ 40 deg

2) Humidity :   ~ 80 %

10

Storage Environment

1) Temp.   : -20 ~ 60 deg 

2) Humidity : ~ 85%

Summary of Contents for 40LH5300






















Reviews: