LG 37LC6D Service Manual Download Page 74

Page: 74 / 75

Copyright © 2008 LG Electronics. Inc. All right reserved. 72 LGE Internal Use Only
Only for training and service purposes

Eccentricity of

button, jack,

and indicator

* B/A x 100%

≥

60%

Air vent holes

follow UL & IEC standards.

AV jacks

When all AV jack is connected, they must be no interrupt

1.2 - External checks

Checking Item

Test SPEC.

Control

Buttons

①

The button mechanism must be smooth to operate and robust.

②

Buttons should not rattle, be too loose, or too tight

Printing

follow LG ID spec. included color, size, font…

Printing Ink

Test

* Test :

Scrub 50 times both ways using JIG. The Jig is 1kgf weight, wrapped the

gauze stained ethyl alcohol. Scraping speed is 30~40times/min.

* Judgments :

Must not be erased.

Kensington

Lock

Add Kensington Lock hole on lower left corner.

Cable

management

Cable management should not be too loose, or too tight.

Summary of Contents for 37LC6D






































Search results

Summary of Contents for 37LC6D

Reviews:

Brands by name

Popular brands

LG 37LC6D, Service Manual

Search results

Summary of Contents for 37LC6D

Reviews:

Brands by name

Popular brands