LG 29FU1RNX, Service Manual, Page: 11 / 39

?W&?
W&@L ?W&@@)X?
W&@@@@)X ?O&@@@@@@1
?W2@@@@@@@@@L? O&@@@@@@@@@@)K ?@@@@@@@@@@@@@@@@?hg
?3@@@@@@@@@@@@(M ?V'@@@@@@@@@@(Y?
V'@@@@@@@@(Y ?N@@@@@@@0Y?
3@@@@@ V'@@@5
?V'@(Y V+Y?
Change signal into cross-hatch pattern in order to adjust
horizontal pin-cushion.
? ?
? ?
? ? ?
? ?
? ?
W&he? ?W&@L?h?
W&@@)Xh? ?W&@@@@)X?g?
W&@@@@@@)Xg? ?W&@@@@@@@@)X?f?
W&@@@@@@@@@@)Kf? 7@@@@@@@@@@@@@(?e?
3@@@@@@@@@@@@(Y?e? V'@@@@@@@@@@(Yf?
?V'@@@@@@@@(Y?f? V'@@@@@@(Yg? ?V'@@@@(Y?g?
V'@@(Yh? ?V'@H?h?
V'he? ?
? ?
? ?
?
After above adjustments, re-adjust EW, EP, ANGLE, BOW,
CRNU, CRNL and finish Pin Cushion adjustment.
(14) After finish adjustment press “OK” key to save changes.
1) In the PAL 100Hz mode “ENTER” just works in initial
adjustment mode and if press ENTER key after the
adjustment in other input signal, it saves the adjustment
data of corresponding mode. (NON-EU
? ?
? ?
? ? ?
? ?
? ?
? ?
? ?
?)X?g? ?3)Xg?
?V@)X?f? ?@@@@@@@@@@@@@)?f?
?@(Mg? ?(Y?g?
? ? ?
? ?
? ?
? ?
? ?
?
PAL 100Hz)
2) In the PAL 100Hz mode “ENTER” saves the setting
value of the other input signal mode based on the data
of initial adjustment mode.
(use this for the adjustment of initial production)
3) In the PAL(50p) and NTSC modes ,“ENTER” saves the
adjustment value of corresponding mode not relating
with other input signal mode.
(15) After finish the adjustment in initial mode, apply re-
adjustment checking adjustment status of other input
signal.
(16) When adjust NTSC mode of the BG/I/DK system
model, input the NTSC signal to the AV3
(Use the pattern of the 13CH (NTSC/J-03) and the
crosshatch)
12.3. Initial data for deflection adjustment.
Deflection adjustment basis DATA for each deflection mode
?
? ?
?
? ?
? ?
? ?
?
? ?
? ?)X?g?
?3)Xg?
?V@)X?f? ?@@@@@@@@@@@@@)?f?
?@(Mg? ?(Y?g?
? ?
?
? ?
? ?
? ?
?
? ?
? ?
Refer to APPENDIX
(Note) Deflection initial DATA is compensated automatically
against standard mode store value with “ENTER”
after finishing adjustment at standard mode (NON-EU :
PAL 100Hz)
13. Checking Wireless Sound function
(X-WAVE) (Option)
(1) Wireless sound model’s efficiency inspections is
executed to a finished in a final inspection phase.
(2) Wireless sound is a function which transmits a FM signal
through transmitter of inner part in DIGITAL BOARD
into outer AV receiver, Radio and so on.
(3) If the received frequency which is set up in OSD is being
tuned without using an exclusive remote
it is available to receive in a general FM receiver.
(4) How to inspect condition of a transmission and reception
in this mode.
1) Execute in channel generating voice-signal.
2) Select a transmitted frequency in MENU OSD : MENU
?
? ? ?
? ?
? ?
? ?
? ?
? ?
? ?)X?g?
?3)Xg? ?V@)X?f?
?@@@@@@@@@@@@@)?f? ?@(Mg? ?(Y?g?
? ?
? ?
? ?
? ?
? ?
? ?
SOUND
?
? ? ?
? ?
? ?
? ?
? ?
? ?
? ?)X?g?
?3)Xg? ?V@)X?f?
?@@@@@@@@@@@@@)?f? ?@(Mg? ?(Y?g?
? ?
? ?
? ?
? ?
? ?
? ?
X-WAVE
?
? ? ?
? ?
? ?
? ?
? ?
? ?
? ?)X?g?
?3)Xg? ?V@)X?f?
?@@@@@@@@@@@@@)?f? ?@(Mg? ?(Y?g?
? ?
? ?
? ?
? ?
? ?
? ?
Select frequency (Ex. 87.7MHZ)
3) A received frequency in an exclusive remote control or
received FM Radio is tuned by 87.7MHz which is same
as frequency in OSD.
4) Check if a signal generating to a SPEAKER generates
in earphone or receiver
5) There is no alternation and setting of adjusted DATA in
the process of inspecting FM TX.
14. OPTION Adjustment
14-1. Preliminary steps
(1) This adjustment decides functions in accordance with
model.
Press the SVC TX adjustment button (IN-START button) at
SVC mode, and then adjust the option at OPTION 1, 2, 3,
4, 5 modes.
(2) Mark the option adjustment data like [xxx,xxx,xxx,xxx,xxx]
in BOM.
14-2. Adjustment
(1) Each OPTION value can be input using remote controller’s
number key. (Each option data store automatically.)
(2) At each OPTION mode, select adjustment item by the
CH ?@e J5e
7He ?J5?e ?7H?e
J5f 7Hf
?J5?f ?7H?f
J5g 7Hg
?J5?g ?7H?g
J5h 7Hh
?J5?h ?7H?h
J5he 7Hhe
@?he
button and then set up each OPTION by the
VOL / button.
14-3. OPTION table
[OPTION 1]
[OPTION 2]
- 11 -
NON-EU
EU/CIS
Area Adjustment Order
PAL(50p)
Store This Mode
?
? ?
? ?
? ?
? ?
? ?
W&he? ?W&@L?h?
W&@@)Xh? ?W&@@@@)X?g? W&@@@@@@)Xg?
?W&@@@@@@@@)X?f? W&@@@@@@@@@@)Kf?
7@@@@@@@@@@@@@(?e? 3@@@@@@@@@@@@(Y?e?
V'@@@@@@@@@@(Yf? ?V'@@@@@@@@(Y?f?
V'@@@@@@(Yg? ?V'@@@@(Y?g?
V'@@(Yh? ?V'@H?h?
V'he? ?
? ?
? ? ?
Example
LEVEL PAPT NO. SPECIFICATION DESCRIPTION
1 31419MNxxxA MAIN CHASSIS ASSY OPT[122,084,006,511,000]
?
? ?
? ?
? ?
? ?
? ?
W&he? ?W&@L?h?
W.MI/Xh? ?W.YeV/X?g? W.Y?e?V/Xg?
?W.YgV/X?f? W.Y?g?V/Kf?
7HheN@(?e? 3LheJ(Y?e?
V/X?g?W.Yf? ?V/XgW.Y?f?
V/X?e?W.Yg? ?V/XeW.Y?g?
V/KO.Yh? ?V'@H?h?
V'he? ?
? ? ?
? ?
OPTION1 data is 122,OPTION2 data is 084,OPTION3 data is 006,
OPTION4 data is 511, and OPTION5 data is 000 in this model.
NTSC
Store This Mode
PAL(100Hz)
Store All Mode
NO
1
2
3
4
5
CODE
SYS
200PR
ACMS
TEXT
CH+AU
FUNCTION
1: BG/I/DK/M
0: BG/I/DK
1: 200PR
0: 100PR
1:WITH CHANNEL NAME DISPLAY
0: WITHOUT CHANNEL NAME DISPLAY
3: AUTO
2: FLOP
1: TOP
0: OFF
1: CHINA+AUSTRAILIA CHANNEL TABLE
0 : OTHER CONTRIES CHANNEL TABLE
REMARK
1: NON-EU
0: EU/CIS
1: Without Teletext
0: With Teletext
1:All countries except Australia
0:Australasia only
3: EU (Installation Guide ON)
2: FLOP (NON-EU)
1: TOP (countries except EU Area)
0: Without Teletext
1 : China, Australia
0 : Others
NO
1
2
3
4
5
CODE
FMTM
A2 ST
HDEV
V-Curve
1 2 SAVE
FUNCTION
1 : Enable XWAVE
0 : NO XWAVE
1 : FM STEREO/DUAL Enable
0 : FM STEREO/DUAL Disable
1 : HIGH DEVIATION MODULATION
0 : RF NORMAL SOUND MODULATION
1 : RUSHED SOUND CURVE
0 : STANDARD SOUND CURVE
1 : FM STEREO / DUAL
0 : MONO
REMARK
1:
0:
1 : Others
0:Tunisia
1:China/Saudi/India/Indonesia/Leb
anon/Pakistan/Iran
0 : Others
1 : NON-EU
0 : EU/CIS
1 :
0 : Only MONO OSD